Panasonic PT-TW230E - Page 53

-53-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000
11 CR - GAIN AREA V START 500 0 - 1000
12 Image AREA H WIDTH YCBCR Level Acquiring Area 13 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 4 0 - 255
15 CB OFFSET TARGET 128 0 - 255
16 CR OFFSET TARGET 128 0 - 255
17 Y - GAIN TARGET 217 0 - 255
18 CB - GAIN TARGET 237 0 - 255
19 CR - GAIN TARGET 237 0 - 255
20 OFFSET torelance Torelance of OFFSET Adj. 1 1 - 255
21 GAIN torelance Torelance of GAIN Adj. 1 1 - 255
Group
270
CUSTOM(Aspect)
0 Scaler Horizontal Scaler Horizontal 100 68 - 132
1 Scaler Vertical Scaler Vertical 100 68 - 132
2 Connect 0:Individual 1:Normal 0 0 - 1
3 Position Horizontal Position Horizontal 100 85 - 115
4 Position Vertical Position Vertical 100 85 - 115
5 Aspect Enable TRUE:Enable FALSE:Disable 0 0 - 1
Group
280
AutoPC Adjust
0 AutoPCAdjustEnable
Auto-PC Adj Operation Enable
if Un-supported Signal Input
0 0 - 1 0: Enable, 1: Disable
1 Frequency Step Frequency Steps of TotalDot 1 0-3
2 Frequency Threshold Total Dot Frequency Threshold 5 0 - 10 0 [] <--- -----> 10[Not matched]
3 Fine Phase
Do Phase Adj after Total Dot
Adj.
1 0 - 1
0: Executes Fine Phase, 1: Not
Execute
4 BLKDET Black Level Detection Area 1 0 - 7
5 PHASEMSK Phase Detection Filter 0 0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
2: Disable Lower 2 bit, 3: Disable
Lower 3 bit
Group
290
Panel Type
0 GammaL/R-View 0 0-20
0: Gamma for L-Turn
20: Gamma for R-Turn * Read
only
1 GammaL/R-Change
Sets L-Turn Gamma if the Value
is set to 0.
Sets R-Turn Gamma if the
Value is set to 20.
10 0-20
Group
430
Model No. Setting [No Name]
0 Model No. Confirm
0:No Name
1:PT-TW230 / PT-TW231R
2:PT-TW230U / PT-TW231RU
3:PT-TW230E / PT-TW231RE
4:PT-TW230EJ / PT-TW231REA
5:PT-TW230EA / PT-TW231REA
6:PT-TW230EAJ / PT-TW231REAJ
7:PT-XW23ST / PT-XW25SR
0 -
1 Model No. Setting
Model No. is set when the value
is set 0 to 10.
0 0 - 10
Group
431
Model No. Setting [PT-TW230 / PT-TW231R]
0 Model No. Confirm * Refer to S430-0 0 -
1 Model No. Setting
Model No. is set when the value
is set to 10.
0 0 - 10
Group
432
Model No. Setting [PT-TW230U / PT-TW231RU]
0 Model No. Confirm * Refer to S430-0 0 -
1 Model No. Setting
Model No. is set when the value
is set to 10.
0 0 - 10
Group
433
Model No. Setting [PT-TW230E / PT-TE231RE]
0 Model No. Confirm * Refer to S430-0 0 -
1 Model No. Setting
Model No. is set when the value
is set to 10.
0 0 - 10
Group
434
Model No. Setting [PT-TW230EJ / PT-TW231EJ]