Panasonic PT-TW380

Questions and Answers:

A
alexanderpatriciaAug 17, 2025
How to fix a Panasonic PT-TW380 that does not turn on?
- B
  Benjamin PerezAug 17, 2025
  If your Panasonic Projector isn't powering on, several things could be the cause. First, make sure the power cord is properly connected to both the projector and a working wall outlet. Check that the wall outlet has electric supply. Also, verify that the circuit breakers haven't tripped and reset them if necessary. Ensure that the lamp cover is securely installed. Finally, check the warning indicator light to see if it's lit or blinking, as this could indicate a specific issue.
N
Nicole MillerAug 20, 2025
What to do if no picture appears on Panasonic PT-TW380 Projector?
- F
  floresjessicaAug 20, 2025
  If no picture is showing on your Panasonic Projector, start by checking that the video signal input source is correctly connected to the appropriate terminal. Ensure that the input selection setting on the projector is correct. Adjust the [BRIGHTNESS] setting, as it may be at its minimum. Verify that the input source connected to the projector is working correctly. Finally, confirm that the AV mute function is turned off.
L
Lynn EricksonAug 22, 2025
Why is the Panasonic PT-TW380 Projector remote control not operating?
- J
  Jeffrey RuizAug 22, 2025
  If the remote control for your Panasonic Projector isn't working, first replace the batteries, ensuring they are inserted correctly. Remove any obstructions between the remote and the projector's signal receptor. Make sure you're within the remote's operational range. Avoid strong light shining onto the signal receptor. Check that the [REMOTE CONTROLLER] setting is set to [ENABLE] in [CONTROL DEVICE SETUP]. Lastly, ensure the same code is set on both the projector and remote control.
M
michael65Aug 26, 2025
What to do if Panasonic PT-TW380 Projector picture does not display correctly?
- D
  Dana SmithAug 26, 2025
  If the picture on your Panasonic Projector isn't displaying correctly, ensure that the [TV-SYSTEM] and [RGB/YC C ]/[RGB/YP P ] selections are set correctly. Check the VCR or other signal source for problems. Make sure you're inputting a signal that's compatible with the projector. Also, verify that the computer output settings are correct.
C
Caroline MullenAug 28, 2025
Why picture from computer does not appear on Panasonic Projector?
- J
  joshua34Aug 28, 2025
  If you're not getting a picture from your computer on the Panasonic Projector, and you're using a D-Sub cable, make sure the cable is 10 m (32'10") or shorter. If it's too long, use a shorter cable. Also, ensure that the external video output on your laptop computer is set correctly.
M
Mr. Dennis MartinezAug 31, 2025
How to fix a fuzzy picture on a Panasonic Projector?
- O
  ocrawfordAug 31, 2025
  If the picture on your Panasonic Projector is fuzzy, try adjusting the lens focus. If that doesn't help, clean the lens. Also, adjust the projector's position relative to the screen to ensure it's set properly.
N
Nancy RiveraSep 2, 2025
Why is there no sound from the internal speaker of my Panasonic PT-TW380?
- F
  Frank LittleSep 2, 2025
  If you're not getting any sound from the internal speaker of your Panasonic Projector, first ensure the external device is correctly connected to the audio input terminal. Increase the volume, as it may be set to the minimum. Make sure the AV mute and the Mute functions are turned off. If something is plugged into the VARIABLE AUDIO OUT, unplug it to enable the built-in speaker. Finally, verify that the audio input selection in [AUDIO SETTING] is set correctly.
S
Stephanie ThomasSep 5, 2025
What to do if HDMI picture is unstable on Panasonic Projector?
- J
  Julie EllisSep 6, 2025
  If the picture from your HDMI device isn't appearing or is unstable on your Panasonic Projector, check that the HDMI cable is securely connected. Try turning off the power of both the projector and the connected devices, then turn them back on. Also, ensure you are only using supported signal cables.
J
Justin Marquez IIISep 8, 2025
Why does the Panasonic Projector display color pale or grayish?
- L
  logan44Sep 8, 2025
  If the color on your Panasonic Projector appears pale or grayish, check and adjust the [COLOR] or [TINT] settings. Ensure the connected input source is properly adjusted. If you're using an RGB signal cable, replace it if it's damaged.
M
Matthew JacksonSep 12, 2025
Why is there no sound from HDMI device on Panasonic PT-TW380 Projector?
- J
  judyedwardsSep 12, 2025
  If there's no sound output from your HDMI device on the Panasonic Projector, change the sound channel of the attached device to Linear PCM. Also, check the audio input selection in [AUDIO SETTING].

Panasonic PT-TW380 Specifications

General

Contrast Ratio	16, 000:1
Lamp Life (Normal)	4, 000 hours
Zoom Ratio	1.6x
Speakers	10 W Mono
Connectivity	HDMI, VGA, USB
Native Resolution	1280 x 800
Keystone Correction	Vertical: ±30°