19
RQT7621
INTRO
You can configure the remote control TV operation buttons to turn
the television on/off, change the television input mode, select the
television channel and change the television volume.
1
Switch [HOME THEATER, TV] to “TV”.
2 Point the remote control at the television
While pressing [Í], enter the code
with the numbered buttons.
e.g., 01: [0] ➡ [1]
Manufacturer and Code No.
Test by turning on the television and changing channels. Repeat
the procedure until you find the code that allows correct operation.
≥If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote
control is not compatible with your television.
∫ The 3 methods for switching to the AV input on
your Panasonic TV
Your Panasonic TV uses one of 3 different methods for switching
between TV reception and the AV input(s). Perform the operations
steps listed for the switching methods A, B and C below to
determine which one your Panasonic TV uses.
Preparation
Switch [HOME THEATER, TV] to “TV”.
A Press [AV] to switch to the AV input. Each press of [AV]
switches between TV reception and AV input(s).
B (for the remote control code No.45)
1 Press [AV]. Colour bars for selecting the AV input appear on the
TV screen.
2 Follow the instructions displayed on the TV screen to select the
desired AV input from the displayed colour bars for the AV input
by pressing [A], [B], [C] or [D] on the remote control.
C (for the remote control code No.01)
1 Press [AV]. The last previously selected AV input indication
appears on the TV screen. The indications for selecting another
AV input also appear, but they disappear a few seconds later.
2 Before the indications for selecting another AV input disappear,
press [A], [B], [C] or [D] to select the desired AV input.
With the following four buttons, you can move and select as follows:
[A]: Move left [C]: Move up
[B]: Move down [D]: Move right
If other Panasonic products are placed close together, change the
remote control code on the main unit and the remote control (the
two must match). Under normal circumstances use the factory set
code “DVD 1”.
1 While stopped
Press [FUNCTIONS].
2 Press [3, 4, 2, 1] to select
“SETUP” and press [ENTER].
3 Press [3, 4] to select “Others” and
press [1].
4 Press [3, 4] to select “Remote
Control” and press [ENTER].
5 Press [3, 4] to
select the code
(“DVD 1”, “DVD
2” or “DVD 3”)
and press [ENTER].
6 To change the code on the remote control
While pressing [ENTER], press and
hold the numbered button ([1], [2] or
[3]) for more than 2 seconds.
7 Press [ENTER].
∫ When the following indicator appears on the
unit’s display
The unit’s remote
control code
Change the code on the remote control to match the main unit’s
(➡step 6).
[Note]
Executing “Shipping Condition” in the SETUP menu returns the
main unit code to “DVD 1”. Change the remote control code to 1
(➡step 6).
Television operation
Brand Code
Panasonic 01, 02, 03, 04, 45
AIWA 35
AKAI 27, 30
BLAUPUNKT 09
BRANDT 10, 15
BUSH 05, 06
CURTIS 31
DESMET 05, 31, 33
DUAL 05, 06
ELEMIS 31
FERGUSON 10
GOLDSTAR/LG 31
GOODMANS 05, 06, 31
GRUNDIG 09
HITACHI 22, 23, 31, 40, 41, 42
INNO HIT 34
IRRADIO 30
ITT 25
JVC 17, 39
LOEWE 07
METZ 28, 31
MITSUBISHI 06, 19, 20
MIVAR 24
NEC 36
NOKIA 25, 26, 27
NORDMENDE 10
ORION 37
PHILIPS 05, 06
PHONOLA 31, 33
PIONEER 38
PYE 05, 06
RADIOLA 05, 06
SABA 10
SALORA 26
SAMSUNG 31, 32, 43
SANSUI 05, 31, 33
SANYO 21
SBR 06
SCHNEIDER 05, 06, 29, 30, 31
SELECO 06, 25
SHARP 18
SIEMENS 09
SINUDYNE 05, 06, 33
SONY 08
TELEFUNKEN 10, 11, 12, 13, 14
THOMSON 10, 15, 44
TOSHIBA 16
WHITE WESTINGHOUSE 05, 06
When other Panasonic products
respond to this remote control
SETUP
Disc
Tuning
Remote Control
Others
Press “±” and “ENTER” together
for more than 2 seconds on the remote
control.
HT1500_EB.book 19 ページ ２００４年５月２８日 金曜日 午後１時４１分
To Next Page
Loading...
