16
VQT5J41
Advanced operations
The main unit is automatically turned off if there is no audio
input and when you do not use it for approx. 2 hours.
While pressing and holding
[CLEAR VOICE] on the remote
control, press and hold [INPUT] on
the main unit for more than 4 sec to
display the current setting.
While the setting is displayed, press
[CLEAR VOICE] to select the setting.
≥ The setting changes each time [CLEAR VOICE] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and
then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.
This function allows you to connect a paired Bluetooth
®
device when the main unit is in standby mode.
While pressing and holding
[SURROUND] on the remote control,
press and hold [ ] on the main unit
for more than 4 sec to display the
current mode.
While the mode is displayed, press
[SURROUND] to select the mode.
≥ The setting changes each time [SURROUND] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and
then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.
You can turn off dimmer mode and keep the LED
indicators bright.
While pressing and holding [INPUT] on
the remote control, press and hold
[s VOL] on the main unit for more than
4 sec to turn off Dimmer mode.
≥ The indicator for the current condition will turn brighter.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is on.
To turn on dimmer mode, repeat the operation above.
After performing the operation, the indicator for the current
condition will be dim.
∫ Remote control code
When other Panasonic devices respond to this system’s
remote control, change the remote control code on this
system and the remote control.
Preparation
≥ Turn off all other Panasonic products.
≥ Turn on the main unit.
Change the remote control code to code 2:
1 Aim the remote control at the main unit’s
remote control sensor.
2 Press and hold [MUTE] and [ ] on the remote
control for more than 4 sec.
≥ All the indicators will blink for 10 sec when the code of
this system is changed.
≥ The setting is maintained until it is changed again.
≥ If the main unit does not operate after changing the code,
repeat steps 1 and 2.
≥ To change the remote control code to code 1, repeat the
steps above, but replace
[] with [INPUT].
∫ To turn off the volume limitation
If a state of the lowered volume disturbs you every time
the main unit turns on, for example, it is possible to turn off
this function as follows:
While pressing and holding [MUTE] on the remote control,
press and hold [VOL
i
] on the main unit for more than 4 sec.
≥ All the indicators will blink once when the volume limitation
is turned off.
To reset the setting, return to the factory preset. (> p. 17)
Auto Power Down
“BD/DVD” indicator blinks:
Auto Power Down is on.
“CLEAR VOICE” indicator blinks:
Auto Power Down is off.
Bluetooth
®
Stand-by
“BD/DVD” indicator blinks:
Bluetooth
®
Stand-by is on.
“CLEAR VOICE” indicator blinks:
Bluetooth
®
Stand-by is off.
ャュバュヷュ
ャュバュヷュ
ヤロユモンチヷヰリヤユ
Dimmer mode
Others
ヵヷ
ャュバュヷュ
ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ
ヵヷ
ャュバュヷュ
ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ
SC-HTB8P_VQT5J41_P.book 16 ページ ２０１４年３月２４日 月曜日 午前１０時３５分
To Next Page
Loading...
Need help?
General
Weight and Dimensions
