Why is my Panasonic Home Theater System remote control not working?
If your Panasonic Home Theater System remote control isn't working, first remove the insulation sheet if it's the first time using it. Then, check if the battery is installed correctly. If the battery is weak, replace it with a new one and set the remote control code again. Finally, ensure you are using the remote control within the correct operation range.
How to troubleshoot no power on Panasonic SC-HTB490?
If your Panasonic Home Theater System has no power, first wait about 10 seconds after connecting the AC mains lead before switching on the main unit. If that doesn't work, disconnect the AC mains lead for 10 seconds and then reconnect it. If the unit switches off immediately after being turned on, disconnect the AC mains lead and consult your dealer. Also, if the unit doesn't switch on when you turn on the TV (HDMI CEC), try switching on the main unit manually.
How to fix no sound on Panasonic Home Theater System?
If your Panasonic Home Theater System has no sound, try the following: 1. Cancel muting. 2. Check the connections to the other devices. 3. Ensure the received audio signal is compatible with the system. 4. If connected to the TV with only an HDMI cable, and the HDMI terminal isn't labeled 'HDMI (ARC)', connect an optical digital audio cable. 5. If connections are correct, try changing the cables. 6. Check the audio output settings on the connected device. 7. Try changing the digital audio output setting on the connected device.
What to do if Panasonic Home Theater System device cannot be connected?
If your Panasonic Home Theater System is not connecting to a device, try the following: 1. Do pairing again, because the pairing of the device was unsuccessful. 2. Do pairing again, because the pairing of the device has been replaced. 3. Disconnect other devices, because the system might be connected to a different device and try connecting the device again. 4. Switch off the system and then switch on again, because the system may have a problem.
What to do if device is connected but audio cannot be heard through Panasonic SC-HTB490 Home Theater System?
If you cannot hear audio through your Panasonic Home Theater System even though the device is connected, for some built-in Bluetooth[®] devices, you have to set the audio output to 'SC-HTB490' manually. Consult the operating instructions of the device for specific instructions.
Why pairing cannot be done on Panasonic SC-HTB490?
If you are experiencing pairing issues with your Panasonic Home Theater System, check the Bluetooth[®] device condition. If the device is out of the 10 m communication range, move it nearer to the system.
Why is sound interrupted on Panasonic SC-HTB490 Home Theater System?
If the sound from your Panasonic Home Theater System is interrupted, move the device nearer to the system if it is out of the 10 m communication range. Also, remove any obstacles between the system and the device. If other devices using the 2.4 GHz frequency band are interfering, move the device nearer to the system and distance it from the other devices.
What to do if WIRELESS LINK indicator does not switch on Panasonic SC-HTB490 Home Theater System?
If the WIRELESS LINK indicator on your Panasonic Home Theater System does not switch on, check that the main unit is switched on. The active subwoofer and the main unit may not be paired correctly, so try wireless pairing: switch on the main unit, then press and hold [I/D SET] on the rear of the active subwoofer for at least 3 seconds. You can also try switching off the main unit and then switching it on again. If the problem persists, consult your dealer. Check if the remote control and the main unit are using different codes, and change the code of the remote control if needed.
Why does my Panasonic SC-HTB490 automatically switch to standby mode?
If your Panasonic Home Theater System automatically switches to standby mode, it is likely because the “Auto off” function is on. The system automatically switches to standby mode if there is no signal input and no operation is being performed for approximately 20 minutes. Refer to page 17 to switch off this function.
Why HDMI CEC related operations no longer function properly Panasonic SC-HTB490?
If HDMI CEC related operations no longer function properly on your Panasonic Home Theater System, check the settings on the connected devices. When the HDMI connections are changed, after a power failure, or after the AC mains lead has been removed, HDMI CEC operations may not function properly. Switch on all the devices connected to the TV with an HDMI cable and then switch on the TV. You can also try switching off the HDMI CEC settings of the TV and then switching it on again. While the system and the TV are connected with an HDMI cable, switch on the TV, disconnect the AC mains lead of this system, and then connect it again.
Essential safety guidelines to prevent hazards like fire, electric shock, and injury.
Describes how to connect the system to ARC and non-ARC compatible TVs.
Detailed steps for securely mounting the main unit on a wall.
Steps to establish a wireless link between the main unit and the subwoofer.
Instructions for pairing and connecting Bluetooth audio devices.
Instructions for downloading and installing system firmware updates.
Solutions for problems related to the system not powering on or responding.
Guidance for resolving issues with Bluetooth pairing and connection.
Resolving HDMI CEC problems and troubleshooting no audio output.
Addresses sound lag, subwoofer power/sound issues, and audio format mismatches.
General| RMS rated power | 320 W |
|---|---|
| Audio output channels | 2.1 channels |
| Surround modes quantity | 2 |
| Wi-Fi | No |
| Bluetooth | Yes |
| Bluetooth version | 4.2 |
| Connectivity technology | Wireless |
| Soundbar speaker RMS power | 160 W |
| Power consumption (standby) | 0.5 W |
| Product color | Black |
| Cables included | AC |
| Number of products included | 7 pc(s) |
| Harmonized System (HS) code | 85182200 |
Weight and Dimensions| Depth | 100 mm |
|---|---|
| Width | 800 mm |
| Height | 56 mm |
| Soundbar weight | 8700 g |
| Subwoofer depth | 360 mm |
| Subwoofer width | 170 mm |
| Subwoofer height | 382 mm |
To Next Page
