RQTX1190
ENGLISHENGLISH
1010
■ USB section
USB Port
USB Standard USB 2.0 full speed
Media fi le format support MP3 (
.mp3)
USB device fi le system FAT 12, FAT 16, FAT 32
USB port power 500 mA (Max)
■ Speaker section
Type 1 way, 1 speaker system (Bass refl ex)
Speaker unit(s)
Full range 10 cm cone type
Impedance 6
Output sound pressure 83 dB/W (1 m)
Frequency range 61 Hz to 17 kHz (–16 dB)
95 Hz to 15 kHz (–10 dB)
Dimensions (WxHxD) 139 mm x 224 mm x 136 mm
Mass 1.3 k g
■ General
Power supply AC 220 to 240 V, 50 Hz
Power consumption 12 W
Dimensions (WxHxD) 184 mm x 123 mm x 228 mm
Mass 1.1 k g
Operating temperature range 0°C to +40°C
Operating humidity range
35% to 80% RH (no condensation)
Power consumption in standby mode:
0.3 W (approximate)
1) Specifi cations are subject to change without notice.
Mass and dimensions are approximate.
2) Total harmonic distortion is measured by the digital
spectrum analyzer.
Specifi cations
■ Amplifi er section
RMS Output power stereo mode
Front Ch (both channels driven)
5 W per channel (6
), 1 kHz, 10% THD
Total RMS stereo mode power 10 W
■ FM/AM tuner, terminals section
Preset station FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals 75
(unbalanced)
Amplitude Modulation (AM)
Frequency range
522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz (10 kHz step)
Headphone jack
Terminal Stereo, 3.5 mm jack
Output level (CD, 1 kHz, –20 dB)
0.7 mW + 0.7 mW, 32
(Max)
Music port (top)
Sensitivity
Normal 490 mV, 15 k
High 100 mV, 15 k
Terminal Stereo, 3.5 mm jack
■ Disc section
Disc played (8 cm or 12 cm)
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3
formatted disc)
(3) MP3
MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength 785 nm (CD)
Laser power CLASS 1 (CD)
Audio output (Disc)
Number of channels 2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean
this unit.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
10
Memory reset (Initialisation)
When the following situations occur, refer to the
instructions below to reset the memory:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
To reset memory
1) Disconnect the AC mains lead. (Wait at least
3 minutes before proceeding to step 2.)
2) While pressing and holding down [ 1] on the
main unit, reconnect the AC mains lead.
“– – – – – – – –” appears on the display panel.
3) Release [1].
All the settings are returned to the factory preset.
You will need to reset the memory items.
PM02EP_EN.indd 10PM02EP_EN.indd 10 6/28/2010 12:22:44 PM6/28/2010 12:22:44 PM
To Next Page
Loading...
Need help?
General
Weight and Dimensions
