9
TH-103VX200W
4 Specifications
Power Source 200-240 V AC, 50/60Hz
Power Consumption
Power on 1450 W
Stand-by condition 0.5 W
Power off condition 0.3 W
Plasma Display panel Drive method: AC type 103-inch,
16:9 aspect ratio
Screen size 2,269 mm (W) × 1,276 mm (H) × 2,603 mm (diagonal)
(No. of pixels) 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]
Operating condition
Temperature 0 °C - 40 °C
Humidity 20 % - 80 %
Applicable signals
Colour System NTSC, PAL, PAL60, SECAM, Modified NTSC
Scanning format
525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) /
60i 60p 50i 50p 24p 25p 30p 24sF, 1250 (1080) / 50i
PC signals VGA, SVGA, XGA, SXGA
UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
LAN
RJ45 10BASE-T/100BASE-TX, compatible with PJLink
TM
COMPONENT / RGB IN
Y / G (RCA Pin jack) with sync 1.0 Vp-p (75-ohm)
P
B
/C
B
/B (RCA Pin jack) 0.7 Vp-p (75-ohm)
P
R
/C
R
/R (RCA Pin jack) 0.7 Vp-p (75-ohm)
AUDIO L-R (RCA Pin jack × 2) 0.5 Vrms
PC IN (High-Density Mini D-sub 15 Pin) Y or G with sync 1.0 Vp-p (75-ohm)
Y or G without sync 0.7 Vp-p (75-ohm)
P
B
/ C
B
/ B: 0.7 Vp-p (75-ohm)
P
R
/ C
R
/ R: 0.7 Vp-p (75-ohm)
HD / VD: 1.0 - 5.0 Vp-p (high impedance)
VBS (use HD port) with picture 1.0 Vp-p (high impedance)
without picture 0.3 Vp-p (high impedance)
AUDIO (Stereo mini jack (M3) × 1) 0.5 Vrms
AV IN HDMI 1-4 (TYPE A Connector × 4)
HDMI (Version 1.4 with 3D)
SERIAL External Control Terminal (D-sub 9 Pin) RS-232C compatible
3D SHUTTER OUT (M3 jack × 1, for 3D IR TRANSMITTER)
AUDIO OUT L-R (RCA Pin jack × 2 (L / R))
Output level : Variable (- - 0 dB) [INPUT 1 kHz / 0dB, 10 k-ohm Load]
Accessories Supplied
Remote Control Transmitter N2QAYB000562
Batteries R6 (UM3) Size × 2
Fixing band TMME203 × 2
Dimensions (W × H × D) 2,412 mm × 1,419 mm × 129 mm (141 mm when including protruding portion of terminals)
Mass (weight) approx. 199.0 kg net
Notes:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-2, EN61000-3-3.
To Next Page
Loading...
