Parker Series V14 - Displacement Limiter

5
Parker Hannin
Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series V14
Bulletin HY30-5510-M1/UK
Setting
angle
[degree]
Displace-
ment
[cm³/varv]
Shim
maximum
side
[mm]
Shim mini-
mum side
[mm]
Setting
angle
[degree]
Displace-
ment
[cm³/varv]
Shim
maximum
side
[mm]
Shim mini-
mum side
[mm]
6,5 22 58,5 9,5 20,4 67 32,0 35,5
6,9 23 58,0 10,0 20,8 68 31,5 36,0
7,2 24 57,5 10,5 21,1 69 31,0 37,0
7,5 25 57,0 11,0 21,4 70 30,0 37,5
7,8 26 56,0 11,5 21,7 71 29,5 38,0
8,1 27 55,5 12,0 22,1 72 29,0 39,0
8,4 28 55,0 12,5 22,4 73 28,0 39,5
8,7 29 54,5 13,0 22,7 74 27,5 40,0
9,0 30 54,0 13,5 23,0 75 27,0 41,0
9,3 31 53,5 14,0 23,3 76 26,0 41,5
9,6 32 53,0 15,0 23,7 77 25,5 42,0
9,9 33 52,5 15,5 24,0 78 25,0 43,0
10,2 34 52,0 16,0 24,3 79 24,0 43,5
10,5 35 51,5 16,5 24,7 80 23,5 44,5
10,8 36 51,0 17,0 25,0 81 23,0 45,0
11,1 37 50,0 17,5 25,3 82 22,0 45,5
11,4 38 49,5 18,0 25,6 83 21,0 46,5
11,7 39 49,0 18,5 26,0 84 20,5 47,0
12,0 40 48,5 19,0 26,3 85 20,0 48,0
12,3 41 48,0 20,0 26,6 86 19,0 48,5
12,7 42 47,5 20,5 27,0 87 18,5 49,5
13,0 43 46,5 21,0 27,3 88 17,5 50,0
13,3 44 46,0 21,5 27,7 89 17,0 51,0
13,6 45 45,5 22,0 28,0 90 16,0 51,5
13,9 46 45,0 22,5 28,3 91 15,0 52,5
14,2 47 44,5 23,0 28,7 92 14,5 53,0
14,5 48 44,0 24,0 29,0 93 13,5 54,0
14,8 49 43,0 24,5 29,4 94 13,0 55,0
15,1 50 42,5 25,0 29,7 95 12,0 55,5
15,4 51 42,0 25,5 30,0 96 11,0 56,5
15,7 52 41,5 26,0 30,4 97 10,5 57,5
16,0 53 41,0 27,0 30,7 98 9,5 58,0
16,4 54 40,5 27,5 31,1 99 9,0 59,0
16,7 55 40,0 28,0 31,4 100 8,0 60,0
17,0 56 39,0 28,5 31,8 101 7,0 60,5
17,3 57 38,5 29,0 32,1 102 6,0 61,5
17,6 58 38,0 30,0 32,5 103 5,5 62,5
17,9 59 37,0 30,5 32,8 104 4,5 63,5
18,2 60 36,5 31,0 33,2 105 3,5 64,0
18,5 61 35,5 32,5 33,6 106 2,5 65,0
18,9 62 35,5 32,5 33,9 107 1,5 66,0
19,2 63 34,5 33,0 34,3 108 0,5 67,0
19,5 64 34,0 33,5 34,5 109 0,0 68,0
19,8 65 33,5 34,0 34,5 110 0,0 69,0
20,1 66 33,0 35,0
Displacement limiter V14-110
Note! There always have to be a shim on the minimum side of the -110cc motor. (9 mm)
The -110cc motor will be damaged if set below angles of 6,5°.