Parkside PNTS 1300 B2 User Manual (English)

Other manuals for Parkside PNTS 1300 B2

Translation Of Original Operation Manual52 pages

Operation Manual22 pages

Questions and Answers:

J
Jennifer GlassAug 14, 2025
What to do if my Parkside Vacuum Cleaner has no suction?
- M
  Mr. Austin BennettAug 15, 2025
  If your Parkside Vacuum Cleaner isn't picking anything up, several factors could be at play. Start by checking for blockages in the hose system or jets and remove them. Make sure the suction pipe is properly assembled. Verify that the container is closed and not full; empty it if necessary. Also, inspect the filter to see if it's full or clogged; if so, empty, clean, or replace it. Finally, ensure the ball on the filter basket is correctly positioned by switching the equipment off then on again.
B
bdavidsonAug 18, 2025
Why is my Parkside PNTS 1300 B2 losing suction?
- T
  Tyrone WalkerAug 18, 2025
  A loss of suction in your Parkside Vacuum Cleaner can stem from a few issues. Check the hose system or jets for any blockages and remove them. Ensure the suction pipe is correctly assembled. Confirm that the container is properly closed and empty if it's full. Also, inspect the filter to see if it’s full or clogged; empty, clean, or replace it. In addition, the ball on the filter basket may be incorrectly positioned; switch off the equipment so the ball drops then switch on again.
K
Krista KingAug 21, 2025
Why is my Parkside PNTS 1300 B2 not sucking?
- K
  Katherine RileyAug 21, 2025
  There are several reasons why your Parkside Vacuum Cleaner might have low or no suction: * The hose system or jets could be blocked. Clear any obstructions. * The suction pipe might be incorrectly assembled. Ensure it is correctly assembled. * The container might be open or full. Close or empty the container. * The filter might be full or clogged. Empty, clean, or replace the filter. * The ball on the filter basket might be incorrectly positioned. Turn the equipment off and on again.
X
xburkeAug 25, 2025
What to do if my Parkside PNTS 1300 B2 won't start?
- C
  Courtney MannAug 26, 2025
  If your Parkside Vacuum Cleaner isn't starting, here are a few things to check: * Ensure the mains voltage is present by checking the plug socket, cable, line, plug, and fuse. If necessary, have an electrical specialist make repairs. * The on/off switch may be defective. Contact customer service for repair.
S
Stacey ReyesAug 27, 2025
What to do if my Parkside PNTS 1300 B2 won't turn on?
- A
  Alexis PhillipsAug 28, 2025
  If your Parkside Vacuum Cleaner doesn't start, begin by checking the plug socket, cable, line, plug, and fuse to ensure mains voltage is present. If there are any issues, have them repaired by a qualified electrical specialist. If the voltage is OK, the on/off switch may be defective and require repair through customer service. The carbon brushes or the motor could also be defective, but no solution is provided for these causes.
N
Nicole BarnettAug 31, 2025
Why does my Parkside PNTS 1300 B2 Vacuum Cleaner have low suction?
- M
  Michele StewartAug 31, 2025
  Low suction in your Parkside Vacuum Cleaner can occur due to several reasons. The hose system or jets might be blocked; clear any obstructions. Ensure the suction pipe is correctly assembled. Check if the container is open and close it, or if it's full, empty it. The filter might also be full or clogged, so empty, clean, or replace it. Lastly, the ball on the filter basket may be incorrectly positioned; switch the equipment off and on again.
S
scarpenterSep 3, 2025
How to fix a Parkside Vacuum Cleaner that won't start?
- E
  Elizabeth BenderSep 4, 2025
  If your Parkside Vacuum Cleaner isn't starting, there could be a few reasons. First, check the plug socket, cable, line, plug and fuse to ensure mains voltage is present; if needed, have an electrical specialist make repairs. A defective on/off switch could also be the problem; this requires repair by customer service. Other potential causes are worn carbon brushes or a defective motor.
S
Scott MaloneSep 6, 2025
Why won't my Parkside PNTS 1300 B2 turn on?
- L
  Logan CochranSep 7, 2025
  If your Parkside Vacuum Cleaner won't turn on, it might be due to a few reasons. Begin by checking the plug socket, cable, line, plug and fuse to ensure they are working properly; if necessary, have an electrical specialist make repairs. Another possibility is a defective on/off switch, which requires repair by customer service. Other potential causes are worn carbon brushes or a defective motor.
H
Holly RubioSep 10, 2025
What causes a Parkside Vacuum Cleaner not to start?
- R
  Roberto TaylorSep 10, 2025
  There are several reasons why your Parkside Vacuum Cleaner might not be starting. It could be due to the absence of mains voltage; check the plug socket, cable, line, plug and fuse, and if needed, have an electrical specialist perform repairs. A defective on/off switch could also be the cause, requiring repair through customer service. Other potential causes are worn carbon brushes or a defective motor.