Parkside PNTS 1300 C3 User Manual (English)

Other manuals for Parkside PNTS 1300 C3

Translation Of Original Operation Manual44 pages

Questions and Answers:

R
randy53Aug 17, 2025
Why is my Parkside PNTS 1300 C3 not sucking?
- D
  David RobersonAug 17, 2025
  There could be several reasons why your Parkside Vacuum Cleaner has low or no suction: * The hose system or jets might be blocked; clear any obstructions. * The suction pipe might be incorrectly assembled; ensure it is assembled correctly. * The container might be open or full; close or empty the container. * The filter might be full or clogged; empty, clean, or replace the filter. * The float in the filter basket might be incorrectly positioned; switch the equipment off so the ball drops, then switch it on again. * The float in the filter basket might be faulty; in this case it should be repaired by Customer Care.
J
Jennifer BartlettAug 20, 2025
Why is my Parkside PNTS 1300 C3 Vacuum Cleaner losing suction?
- N
  Nicole BarnesAug 20, 2025
  There are several reasons why your Parkside Vacuum Cleaner might have low or no suction: * The hose system or jets could be blocked; remove any obstructions. * The suction pipe might be assembled incorrectly; ensure it is assembled correctly. * The container might be open; close it securely. * The container might be full; empty it. * The filter might be full or clogged; empty, clean, or replace it. * The float in the filter basket might be incorrectly positioned; switch the equipment off so the ball drops, then switch it on again. * The float in the filter basket might be faulty; in this case, it requires repair by Customer Care.
P
Paul MackAug 22, 2025
Why is there low or lack of suction in my Parkside Vacuum Cleaner?
- J
  Jamie DavisAug 22, 2025
  If your Parkside Vacuum Cleaner exhibits low or no suction, several factors could be responsible. Check for blockages in the hose system or jets and remove any obstructions. Ensure the suction pipe is correctly assembled. Verify that the container is closed and not full; empty it if necessary. Also, inspect the filter; if it's full or clogged, empty, clean, or replace it. Lastly, check the float in the filter basket; if it's incorrectly positioned, switch the equipment off so the ball drops, then switch it on again. If the float is faulty, it requires repair by Customer Care.
S
Sarah HoustonAug 26, 2025
What to do if the float does not switch off my Parkside PNTS 1300 C3 Vacuum Cleaner?
- C
  Carla BurnettAug 26, 2025
  If the float in the filter basket of your Parkside Vacuum Cleaner does not switch off the appliance, it could be due to these reasons: * The float in the filter basket might not be moving; release the float. * The float in the filter basket might be faulty; in this case it should be repaired by Customer Care.
J
Joshua FryeAug 28, 2025
Why is my Parkside PNTS 1300 C3 blowing out dust?
- F
  Frank YoungAug 28, 2025
  If your Parkside Vacuum Cleaner is blowing out dust or dirt, the filter might not be assembled correctly or is missing. Make sure to use all the required filters and check that they are in the correct position.
S
samanthamclaughlinAug 30, 2025
How to troubleshoot a Parkside PNTS 1300 C3 that does not start?
- N
  Nicholas ShermanAug 30, 2025
  If your Parkside Vacuum Cleaner doesn't start, the issue could stem from several causes: * Check if mains voltage is present by inspecting the plug socket, cable, line, plug, and fuse. If needed, repair through an electrical specialist. * A defective on/off switch may be the culprit, which requires repair through customer service.
J
James GentrySep 2, 2025
What to do if dust is blowing out of my Parkside PNTS 1300 C3 Vacuum Cleaner?
- E
  Erin CarterSep 2, 2025
  If dust or dirt is blowing out of your Parkside Vacuum Cleaner, it is likely that the filter is either not assembled correctly or missing. Ensure that all filters are present and properly installed.
T
Tanner NealSep 5, 2025
Why doesn't the float switch off my Parkside PNTS 1300 C3?
- C
  Christine DavisSep 5, 2025
  If the float in your Parkside Vacuum Cleaner does not switch off the appliance, try releasing the float in the filter basket. If the problem persists, the float may be faulty and require repair by Customer Care.
P
Patrick HarrisonSep 8, 2025
What to do if my Parkside Vacuum Cleaner won't start?
- B
  Bryan YoungSep 8, 2025
  If your Parkside Vacuum Cleaner isn't starting, it could be due to the following reasons: * There may be no mains voltage present. Check the plug socket, cable, line, plug, and fuse. If necessary, have an electrical specialist make repairs. * The on/off switch could be defective. If this is the case, get it repaired through customer service.
A
Andrew RushSep 12, 2025
What to do if my Parkside PNTS 1300 C3 Vacuum Cleaner doesn't start?
- A
  Angelica Johnson MDSep 12, 2025
  If your Parkside Vacuum Cleaner isn't starting, there could be a few reasons: * There might be no mains voltage. Check the plug socket, cable, line, plug, and fuse. If necessary, have an electrical specialist make repairs. * The on/off switch could be defective. This requires repair through customer service. * The carbon brushes may be worn. * The motor may be defective.