Need help?Do you have a question about the Partner K650 ACTIVE III and is the answer not in the manual?
Explains warning symbols and safety icons found on the power cutter itself.
Explains symbols used within the operator's manual for instructions and warnings.
Details essential protective gear required for safe operation of the power cutter.
Covers the built-in safety features of the power cutter and their inspection.
Describes the vibration damping system designed to reduce user fatigue and enhance comfort.
Explains how to use the stop switch to safely turn off the engine.
Details the function and safety precautions related to the hot muffler.
Emphasizes the importance of the blade guard for preventing injury from the cutting blade.
Provides overarching safety rules for operating the power cutter responsibly.
Covers crucial safety measures for handling, mixing, and storing fuel.
Outlines basic safety practices for operating the power cutter in various conditions.
Provides specific safety advice for the cutting operation, including distance and grip.
Explains the correct method for cutting with the power cutter to ensure efficiency and safety.
Discusses the use of water cooling for specific cutting tasks and its advantages/disadvantages.
Addresses the dangerous phenomenon of kickback and how to avoid it.
Explains how the cut closing can cause the cutter to pull down suddenly and how to avoid it.
Provides instructions on how to properly maintain and store the power cutter.
Introduces the two standard types of cutting blades: abrasive discs and diamond blades.
Details the composition, performance factors, and types/uses of abrasive cutting discs.
Discusses blades manufactured for high-speed portable cutters and compatibility.
Mentions specialized blades for stationary equipment and warns against their use on portable cutters.
Explains how to check blade approval for speed and avoid using blades with lower ratings.
Lists checks for blade damage, including testing abrasive discs and avoiding dropped blades.
Describes diamond blades, their types, uses, material, and water cooling requirements.
Identifies and labels the various components of the power cutter through a diagram.
Details how to inspect the drive shaft and flanges for damage and cleanliness before assembly.
Provides step-by-step instructions for correctly mounting the cutting blade onto the power cutter.
Stresses the importance of fitting and adjusting the blade guard for user safety.
Explains the importance of correct petrol and two-stroke oil mixture ratios for engine performance.
Outlines the safety procedures and steps for refuelling the power cutter to prevent fire and spills.
Details the procedure for starting the power cutter when the engine is cold, including choke use.
Describes the process for starting the power cutter when the engine is already warm.
Explains the simple procedure for stopping the engine using the stop switch.
Instructions on how to properly tension the drive belt for optimal performance.
Step-by-step guide on how to replace the drive belt when necessary.
Safety note regarding the belt pulley and clutch during maintenance.
Information on the carburettor's function and basic troubleshooting for performance issues.
Explains the location, maintenance, and replacement schedule for the fuel filter.
Details the cleaning and replacement of the air filter to maintain engine performance and prevent damage.
Shows the operation of the water valve for cooling systems.
Instructions for checking and cleaning the water filter.
Covers precautions and procedures for replacing starter components like cords and springs.
Step-by-step guide on how to replace a damaged starter cord.
Details the process of tensioning the recoil spring correctly after maintenance.
Instructions for correctly reinstalling the starter unit onto the power cutter.
Explains how spark plug condition affects engine performance and provides maintenance guidance.
Describes the components of the cooling system and the importance of regular cleaning.
Information on the muffler's role in noise reduction and exhaust management, including safety warnings.
Lists essential checks and cleaning tasks to perform on the power cutter daily.
Outlines recommended maintenance tasks to be performed on a weekly basis.
Details the periodic checks and maintenance required for the power cutter each month.
Lists detailed technical data for the engine, including volume, bore, stroke, and speed.
Provides manufacturer and type details for the ignition system and fuel/lubrication system.
States the weight of the power cutter and its noise emission levels according to regulations.
Details vibration levels and specifications for cutting blades and gear ratios.
Official declaration of the power cutter's compliance with relevant European directives and standards.
To Next Page
General