Peavey CS 200X User Manual

Specifications
CHARACTERISTICS (@ 120 V AC, 60 Hz)
Output Power: (Typical Value)
[Impedance Selector Setting]
Stereo mode, both channels driven
2 ohms, 1 kHz, 1% THD
-
110 W RMS per channel [4 ohms]
4 ohms, 1 kHz, 1% THD
- 85 W RMS per than [4 ohms], 120 W RMS per than [8 ohms]
8 ohms, 1 kHz, 1% THD
- 85 W RMS per than [8 ohms], 120 W RMS per than [ 16 ohms]
16 ohms, 1 kHz, 1% THD -
85 W RMS per than [16 ohms]
Bridge mode, mono
4 ohms, 1 kHz, 1% THD
- 220 W RMS [4 ohms]
8 ohms, 1 kHz, 1% THD
- 170 W RMS [4 ohms], 240 W RMS [8 ohms]
16 ohms, 1 kHz, 1% THD -
170 W RMS [8 ohms], 240 W RMS [16 ohms]
32 ohms, 1 kHz, 1% THD -
170 W RMS [16 ohms]
Rated Output Power:
Stereo mode, both channels driven
4 ohms, 20 Hz to 20 kHz, 0.1% THD - 75 W RMS per than [4 ohms]
8 ohms, 20 Hz to 20 kHz, 0.07% THD
- 75 W RMS per than [8 ohms]
16 ohms, 20 Hz to 20 kHz, 0.05% THD
- 75 W RMS per than [ 16 ohms]
Bridge mode, mono
8 ohms, 20 Hz to 20 kHz, 0.1% THD
- 150 W RMS [4 ohms]
16 ohms, 20 Hz to 20 kHz, 0.07% THD
-
150 W RMS [8 ohms]
32 ohms, 20 Hz to 20 kHz, 0.05% THD
-
150 W RMS [16 ohms]
Distortion: (Typical Value)
Stereo mode, both channels driven
20 Hz to 20 kHz, @ rated power & load
-
Below 0.1% [4 ohms], 0.07% [8 ohms], 0.05% [ 16 ohms]
Input Sensitivity & Impedance:
Input attenuator set FCW
@ rated power & load - 0.7 V RMS (-3 dBV) [4 ohms], 1.0 V RMS (0 dBV) [8 ohms],
- 1.4 V RMS (+3 dBV) [ 16 ohms], 20 K ohms (28 dB gain)
Slew Rate: (Typical Value)
Stereo mode, each channel
-
15 volts per uSec
Bridge mode, mono
- 30 volts per uSec
Frequency Response: (Typical Value)
Stereo mode, both channels driven
‘1 dB, 1 W RMS @ rated load
-
lOHzto40kHz
‘0.2 dB, @ rated power & load
-
20 Hz to 20 kHz
Damping Factor: (Typical Value)
Stereo mode, both channels driven
@ rated load, 1 kHz
-
Greater than 100 [4 ohms], 200 [8 ohms], 400 [ 16 ohms]
Hum & Noise:
Stereo mode, both channels driven
Below rated power, unweighted
-
97 dB [4 ohms], 100 dB [8 ohms], 103 dB [16 ohms]
Power Consumption:
Stereo mode, both channels driven
@ rated power & load
- 2.5 A @ 120 V AC
Dimensions & Weight:
H - 1.75” (4.4 cm), W - 19” (48.3 cm), D - 8” (20.3 cm), N - 22 lbs. (10.0 kg)
8

Peavey CS 200X Specifications

General

Brand	Peavey
Model	CS 200X
Category	Amplifier
Language	English