EasyManuals Logo

Peavey GPS Series User Manual

Peavey GPS Series
72 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #17 background imageLoading...
Page #17 background image
17
GPS
2600 SPECIFICATIONS
Rated Power (2 x 2 ohms) - 1,300 watts @ 1 kHz both channels driven at <0.15% T.H.D.
Rated Power (2 x 4 ohms) - 950 watts @ 1 kHz both channels driven at <0.1% T.H.D.
Rated Power (2 x 8 ohms) - 650 watts @ 1 kHz both channels driven at <0.1% T.H.D.
Rated Power (1 x 2 ohms) - 1,500 watts @ 1 kHz at <0.1% T.H.D
Rated Power (1 x 4 ohms) - 1,000 watts @ 1 kHz at <0.1% T.H.D
Rated Power (1 x 8 ohms) - 700 watts @ 1 kHz at <0.05% T.H.D
Minimum Load Impedance - 2 ohms
Maximum RMS Voltage Swing - 93 volts
Frequency Response - 10 Hz - 100 kHz; +0, -.3 dB at 1 watt
Power Bandwidth - 10 Hz - 40 kHz; +0, -3 dB at rated power
T.H.D. (2 x 2 ohms) - <0.15% @ 1050 watts from 20 Hz to 20 kHz with both channels driven
T.H.D. (2 x 4 ohms) - <0.1% @ 900 watts from 20 Hz to 20 kHz with both channels driven
T.H.D. (2 x 8 ohms) - <0.1% @ 600 watts from 20 Hz to 20 kHz with both channels driven
Input CMRR - > - 65d B @ 1 kHz
Voltage Gain - x 40 (32 dB)
Crosstalk - > -75 dB @ 1 kHz at rated power @ 8 ohms
Hum and Noise - > -110 dB, “A” weighted referenced to rated power @ 8 ohms
Power Consumption - > 1200 watts
Slew Rate - > 40V/us
Damping Factor (8 ohms) - > 700:1 @ 20 Hz to 1 kHz
SMPTE IMD - <0.1% 60 Hz and 7 kHz, 900W @ 4 ohms
Input Sensitivity (x 40) - 1.54 volts for 4 ohm rated power, 1.27 volts for 2 ohm rated power
Input Impedance - 20 k ohms, balanced
Current Draw @ 1/8 power@ 2 ohms - 10 A @ 120 volts
Cooling - Two 80 mm DC fans, off until heatsinks reach 45
0
C, then temperature dependant
variable speed
Controls - Two front panel attenuators
Indicator LEDs - Two Clip, two Signal, two Active
Protection - Thermal, DC, turn-on bursts, subsonic, incorrect loads
Connectors - XLR input, 6.3 mm phone type output patch, Speakon and Binding Post speaker
output, IEC mains input
Construction - 16 ga. steel reinforced with 12 ga.rack ears
Dimensions - 133 mm x 483 mm x 432 mm, 400 mm behind rear mounting ears
(5.23" x 19" x 17", 15.75" behind rack ears)
Weight - 45.7 lbs. (20.7 kg)
Specifications subject to change without notice.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Peavey GPS Series and is the answer not in the manual?

Peavey GPS Series Specifications

General IconGeneral
Channels2
Rack Spaces2U
InputsXLR, 1/4"
OutputsSpeakon, Binding Post
ProtectionThermal, short circuit
Dimensions19" (483 mm) W

Related product manuals