Peavey SRC 1600 - Channel Section

CHANNEL SECTION
GAIN (1)
Varies ihe gam of trie channel input stage to allow a wide input dynamic
range. Proper adjustment of the input gam is aided by observance
of the LIMIT LED.
HIGH (2)
An active lone control (shelving type. ±15 dB) that varies the high
frequency boost or cut.
MID/FREQUENCY (3)
The (inner) "MID” is an active control capable of 15 dB of boost o r
cut at the center frequency selected by the (outer) ‘FREQUENCY’
control. Frequency range is variable ; rorr 200 Hz to 5 kHz.
LOW (4)
An active tone control (shelving type, ±15 dB) that varies the low fre¬
quency boost or cut
AUX A (5)
Regulates the amount ol signal routed to the AUX A Master control.
This control is Pre (before) EQ and Pre Fader
AUX B (6)
Regulates trie amount of signal routed to the AUX B Master control.
This control is Pre (before) EQ and Pre Fader.
AUX C (7)
The AUX C control regulates the amount of signal routea to the
AUX C Master control.
AUX D (8)
The AUX D control regulates the amount of signal routed to the
AUX D Master control.
PRE/POST SWITCH (9)
The PRE/POST switch will choose whether the AUX C sgnal is taken
PRE-EQ.FADER (Out position) or POST-EQ'FADER (In position).
NOTE: PREfPOST switch is functional on both AUX C and AUX D
sends.
NOTE: PRE send controls are normally used for creating e monitor
mix.
POST send controls are normally used for outboard effects.
AUX E/F (10) (11)
Two AUX sends are provided in a d uai-concentric control. The inne r
knob is AUX E (10); the outer Is AUX F (11). Both sends are Post
(after) EQ and Post Fader. The AUX E Send routes signal to the AUX E
Master control. The AUX F Send routes signal to the AUX F Master
control
PAN (12)
For stereo ooeration. PAN Is used to mux the channel ouiput to left,
right, or in between in the "stereo image.’' For mono or submaster¬
ing operation, the PAN con:rcl is used with the assigment switches
to pan the channel ouiput between Submasters 1 or 2 when Ihe '-2
button is pressed, Submasters 3 or 4 when the 3-4 button is pressed,
and direct to L or R when the L-R button is pressed
LIMIT LED (13)
Indicates when the signal level in the channel is too high. It illuminates
when the channel signal reaches approximately +15 dBV
PFL (14)
Allows cueing of any channel or combination ol channels instantly
through neadphones connected to the headphone jack (master sec¬
tion). All channel functions (except fader) may be monitored via Ihe
channel PFL system
L-R (15)
When depressed this button allows the channe 1 to send its ouiput
through the PAN control, which will now "crossfade’ between Out¬
put Masters Left and Right. With this c unction engaged. Pan control
L position d rects output to the Left Output Master, center position will
output io both Masters equaly. and in the R position Ihe output wll
be sent to the Right Output Master.
1-2 ( 16 )
When depressed, this button allows the ebanne to send its output
tlrojgh the PAN conirol, which wit now ’crossfade' between Sub¬
masters 1 and 2. With this function engaged Pan control L position
directs output to Submsster 1 center position will output to both sub¬
masters equally, and in the R position the output will be sent to Sub-
master 2
3-4 (17)
When depressed this button allows the channel to send ns output
through the PAN control, which will now "crossfade” between Sub¬
masters 3 and 4 With this function engaged Pan control L position
directs output to Submasler 3. center position will output to both Sub¬
masters equally, and in the P position the output will be sent to trie
Submaster 4.
CHANNEL LEVEL FADER (18)
Determines the level of trie channel. Calibration is in dB and level is
variable from infinity (off) to +10 d3. This should be operated near
the '0 dB” (unify gain) indicator whenever possible to assure an op¬
timum balance between channe noise and headroom.
SUB 1 ARRAY (19)
A calibrated LED array « provided to visually indicate the output level
Of SUB 1
SUB 2/PFL ARRAY (20)
A calibrated, switch-selectable LED array s provided to visually in¬
dicate the output level of Sub 2 or PFL.
SUB 2/PFL SELECT (21)
Switch Out position selects Sub 2; Switch In position selects P = L
SUB 3/L ARRAY (22)
A calibrated, switch-selectable LED array ts provided to visuaily in¬
dicate the output level ol Sub 3 or Left.
SUB 4/R ARRAY (23)
A calibrated. switch -selectable LED array is provided to visually in¬
dicate the output level ol Sub 4 or Right.
SUB 3/LEFT SELECT AND SUB 4/RIGHT SELECT (24)
Switch Out position seects Sub 3; Switch In position selects Left
Switch Out position selects Sub 4; Switch in position selects Right.
AUX A RETURN SECTION
LEVEL (25)
Controls the level of the AUX "A" Return. When an outboard effects
device is patched nto trie AUX "A” patch loop this control deter¬
mines the level ot ihe effect that is routed thru the AUX "A' ’ Pan control.
PAN (26)
Assigns AUX "A" return to Left, Right, or botn. Must be used in con
junction with AUX ”A” Return Level
AUX B RETURN SECTION
LEVEL (27)
Controls the level ol tne AUX ' B" Return. When an outboard effects
device is patched into the AUX "B" patch loop this conirol deter-