EasyManuals Logo

Peavey VIP 1 User Manual

Peavey VIP 1
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #27 background imageLoading...
Page #27 background image

Turn this knob to select your amp model. Each amp has 3 channels: if the LED is red, you are on the high
gain channel, yellow for medium gain and green for low gain. When you are using an acoustic preset (Item 1,
Bank C) only the acoustic amplifiers will be available. If you are using a bass preset (Item 1, Bank D) only the
bass amplifiers will be available. Press and hold for 2 seconds to enter tuner mode.
The LEDs around the Amp encoder will tell you what note you are tuning. At the same time the LEDs around
Effects encoder (Item 4) will indicate whether the note is sharp or flat. If the LED is to the right of the 12:00
position you are sharp (tune down). If the LED is to the left of the 12:00 position you are flat (tune up).
When all of the LEDs around the Effects encoder come on, you are in tune.

Turn this knob to select any “Rack” effect. These are effects you might find attached to the effects loop of an
amplifier. Press the encoder momentarily to enter Edit mode.

Turn this knob to crank up the gain—think of it as how much distortion you want out of the amplifier. In Edit
mode this knob controls parameter 1 of either the selected Stompbox or Effect.


Low EQ adjustment. In edit mode this knob controls parameter 2 of either the selected Stompbox or Effect.

Mid EQ adjustment. In edit mode this knob controls the Feedback of the Delay effect. Feedback is the
number of times the delay repeats.
3
4
5
6
7
10
12 13 14 15 16
5 76 8 9
electric 1
electric 2
acoustic
bass
select type of
inst. for input
aux inUSB phones
0
7
8
1
2
3
4
5
6
10
11
9
12
13
Aphs/Aflg
Comp/Bst
Wah/Slice
Achr/Uvb
Rmd/Slap
Bari/Bss
evio/Syn
Res/Sit
12Str/7Str
Acs1/2
BYPASS
Tsc/Fuzz
push to edit
inst/stomp
phaser
octaver
rot. spkr
reverse
Pitch Shftr
m.o.g.
flanger
comp bst
env. filter
chorus
BYPASS
tremolo
push to edit
effectsinstrument type
Twn
Ecous
Peavey
Classic
6534
Budda
Trace
XXX
6505
Trace
Butcher
push for amp chnl
hold for tuner
amplifiers
Acoustic
Bass
British
P1 P2 delay feedback delay level reverb level
edit mode
pre-gain low mid high post-gain
A
B
C
D
guitar
input
master
volume
VIP-2
looper
tap tempo
VYPYR
®
m m
m
m
m
m
Indicates Monophonic Effect
Play one note at a time
m
Indicates Monophonic Effect
Play one note at a time
RED GRN

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Peavey VIP 1 and is the answer not in the manual?

Peavey VIP 1 Specifications

General IconGeneral
Power Output20 Watts
USB InterfaceYes
USB1 x Type B
Footswitch IncludedNo
Speaker1 x 8" Custom Voiced Speaker
Channels2
TypeModeling Combo Amplifier
Inputs1 x 1/4" Instrument, 1 x 1/8" Aux
Outputs1 x 1/8" Headphones
Footswitch I/O1 x 1/4" (Footswitch)
EffectsReverb, Delay, Chorus, Flanger, Octaver, Tremolo

Related product manuals