What to check if my PEERLESS PureFire PF-210 shows a low water error?
Check the boiler water level, low water cut-off, and harness. If a LWCO is not used, a jumper should be placed between terminals #9 and #10, LWCO Contact.
How do I fix a blocked condensate drain on my PEERLESS Boiler?
If your PEERLESS Boiler shows a 'BLOCKED CONDENSATE DRAIN' error, check the condensate tanks, hoses, condensate switch, and harness.
Follow installation instructions in order for a logical sequence.
Definitions for DANGER, WARNING, CAUTION, and NOTICE boxes.
Boiler assembly, inspection, storage, and contractor qualifications.
Installation must comply with state, local codes, and specific standards.
Minimum clearances for boiler installation and use on combustible floors.
Requirements for supplying combustion and ventilation air to the boiler.
Prepare sketches and review sections for installation layout considerations.
Install venting system per codes and approved materials.
Lists approved materials for vent pipes and adhesives.
Guidelines for locating vent and air intake piping for proper function.
Specifies pipe sizes for exhaust vents and air intakes based on boiler model.
Instructions for connecting and installing exhaust and air intake piping.
Procedure for drilling and tapping the vent pipe for combustion analysis.
Steps for safely removing an existing boiler from a common venting system.
Guidelines for sizing water supply/return piping and system preparation.
Boiler operating requirements including pressure and minimum flow rates.
Brief descriptions of key system components like gauges, air separators, and expansion tanks.
Information on using glycol solutions and freeze protection settings.
Fuel piping installation must comply with local codes and NFPA standards.
How to determine required gas flow rate and pipe capacity.
Instructions for installing gas supply piping, including sediment trap requirements.
Procedures for purging, checking gas pressure, and leak testing.
Instructions for adjusting and checking the main gas valve and CO2 settings.
Disposal of condensate according to local codes and proper piping.
Overview of the condensate trap system, collector, and float switch.
Approved materials for condensate piping, avoiding corrosive metals.
Guidelines for sizing condensate drain pipe and tubing.
Instructions for connecting condensate piping and using a condensate pump.
Wiring must comply with local codes and the National Electrical Code.
Diagrams for connecting thermostats, sensors, circulators, and voltage supply.
Wiring diagram for a typical circulator zone relay.
Schematic of boiler wiring and list of internal components.
Description of the boiler control, its safety features, and heating/DHW modes.
Graphical representation and detailed steps of the boiler's ignition cycle.
Information on installation location, vent material, freeze protection, and safety functions.
Detailed explanation of the 8 central heating modes available.
Overview and descriptions of the three domestic hot water modes.
How to view system status, sensor readings, and fault history.
Information on cascading boilers for increased capacity.
Initial checks before starting the boiler, including water, gas, and electricity.
Steps for filling and purging the system with water.
Verifying gas supply pressure and connections.
Verifying boiler operation, setpoints, and shutdown behavior.
Step-by-step instructions for lighting and operating the boiler safely.
How blocking errors are displayed and suggested corrective actions.
How locking errors are displayed and procedures for resetting.
Explains warning errors related to sensors and their corrective actions.
General observations and checks for the boiler during operation.
Annual inspection requirements for safety and performance.
Procedures for cleaning condensate tanks and hoses.
Steps for cleaning the heat exchanger coils for optimal combustion.
Table showing physical dimensions of various boiler models in inches.
Table listing input, output, heating capacity, and efficiency ratings.
Fan speed specifications for ignition, low, and high power modes.
Specifications for the boiler's main control unit and sensors.
Electrical ratings for blower, gas valve, pumps, and total service current.
List of general repair parts and their stock codes for specific boiler models.
Illustrated breakdown of heat exchanger and burner assembly parts.
Detailed list of heat exchanger and burner assembly repair parts.
Illustrated breakdown of general repair parts for PF-210 and PF-399 models.
List of general repair parts and stock codes for PF-210 and PF-399 models.
Illustrated breakdown of heat exchanger and burner assembly parts for PF-210 and PF-399.
Detailed list of heat exchanger and burner assembly repair parts for PF-210 and PF-399.
Displays boiler status like standby, CH/DHW trial for ignition, and demand.
Shows status for freeze protection, store warm hold, and other special functions.
Displays status for ignition failure, flame failure, and ignition retry.
Shows status for blocking errors and lockout errors, including reset instructions.
Displays current supply setpoint, system vent, outdoor temperature, and circulator status.
Allows adjustment of central heating, DHW, time/date, and temperature units.
Displays the last block and lockout messages.
Shows current supply setpoint, fan speeds, flame signal, ignition attempts, and run time.
Configuration options for pump mode, location, vent material, freeze protection, and safety functions.
Settings for CH modes, pump post purge, ramp delay, and max CH rate.
Settings for DHW modes, priority, heat dump, and max DHW rate.
Options to set up service reminders via time, cycles, or date.
Feature to force boiler operation for service and troubleshooting.
Configuration for multi-boiler cascade operation, including addressing and timing.
Options to restore factory or save/restore site default settings.
To Next Page
General