Peg-Perego primo viaggio tri-fix ISIP User Manual

16
Thecarseatisprovidedwith:aboostercushion,two
shoulderpadsandalegprotectorcushion.
8• Tofittheprotectivecushion,itisnecessarytoreleasethe
crotchstrapfirstfromundertheseat.
 9• Oncethisisdone,slipthepaddingontothethecrotch
strap.
10•Oncethisisdone,slipthepaddingontothethecrotch
strap.
11•Tofittheboostercushion,threadthesafetyharness(1)and
thelegdividerstrap(2)throughtheslotsinthecushion.
FigureBshowsthecorrectfittingoftheboostercushion.
WARNING:removetheboostercushionwhenthechildis
bigger.
12•Thesafetyseathandlehasfourfixedpositions.Torotate
it press the two round buttons on the handle and
simultaneouslymoveittotherequiredangle.Ensureit
clicksintoposition.
• PositionA:thein-carposition;Position B:thepositionfor
transportbyhandandforattachmenttoabase,strolleror
chassis; Position C:allowsthesafetyseattorock;Position D:
stopsthesafetyseatfromrocking.
13•Tofitthehood,insertthehoodattachmentsintotheslots
on the safety seat and arrange the rear part of the hood
behindthebackrest.
14•Thehoodhastwopositions.Toraiseorlowerthehood
pushitbackorpullitforward.Toremovethehood,press
the buttons on its attachment points and at the same time
liftitupwards.
• IMPORTANT:thehoodmustnotbeusedtoliftthesafety
seatbecauseitmightdetach.
Instructions for in-car use
• Fitthecarsafetyseatwiththechildonthecarseat,
rememberingtosecurethechildwiththesafetyharness.
15•Insert the webbing of the car seat belt into the two lateral
guidesonthesafetyseat,ensuringthatitistaut,and
engage the buckle of the car seat belt as shown in the
figure.
16•Take hold of the car seat belt again and pass it behind the
backrestofthesafetyseat,insertingitintotherearguide
asshowninthefigure.
17•In the car the handle must be fully lowered forward
towardsthecarseatbackrestasshowninthefigure.The
correct forward position is reached when it clicks into
position.Checkthattheseatbeltistautandlockedto
ensureadequatesafety.
Removing the covers
Toremovethesafetyharnessfromthecarseat:
• Keep the harness buckles fastened so as to avoid errors
whenrefitting.
18•Release the shoulder straps from the metal buckle on the
backofthecarseat(fig.a)andfromthefrontunthread
theharnessfromtheboostercushion.Removethesafety
harness by releasing the metal ends of the leg divider strap
andthewaiststrapfromtheseatshell(fig.b).
19• Toremovethepadding:
• Unthread the four cover fixing tabs from the edge of the
carseat(fig.a).
• Use a flat screwdriver to lever and release the two plastic
protectorsonthesideguidesofthecarseatbelt(fig.b).
• Removethepadding.
Cleaning the padding
• Brushthefabricpartstoremovedustandhandwashata
maximumtemperatureof30°withoutwringing.
• Donotusechlorinebleach.
• Donotiron.
• Donotdryclean.
• Donotremovestainswithsolventsanddonottumbledry.
Fitting
Torefitthepadding:
• Positionontheseat.
• Insertthefourfixingtabsalongtheedgeofthecarseat.
20• Position the two car seat belt side guide protectors with
the openings facing towards the car seat and check that
theyarecorrectlyengaged.

Peg-Perego primo viaggio tri-fix ISIP Specifications

General

Brand	Peg-Perego
Model	primo viaggio tri-fix ISIP
Category	Car Seat
Language	English