What causes a sticky white or blue film on dishes in my Pelgrim GVWC270L Dishwasher?
A sticky white/blue film indicates the rinse aid dosage setting is too high. Reduce the dosage. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
Why does my Pelgrim GVWC270L have spots on stainless steel or silver?
Spots on stainless steel can be caused by some foodstuffs, such as mustard, mayonnaise, lemon, vinegar, salt and dressings, if left for too long. Rinse off these types of foodstuffs if not starting the dishwasher immediately. Consider using 1h 65° with the Speed wash option. All stainless steel can cause spots on silver if they come into contact during dishwashing. Aluminium can also cause spots on dishes. Separate dishes made from different metals, such as silver, stainless steel and aluminium, to avoid marks and tarnishing.
What to do if water remains in my Pelgrim GVWC270L?
If water remains in your Pelgrim dishwasher, start by cleaning the coarse and fine filters. Also, check that the filters are fitted correctly. Inspect the drainage pump for any debris and clean it if necessary. Ensure the yellow drainage pump stop is in place. Check the drainage hose for kinks or sharp bends. Finally, disconnect the drainage hose from the sink unit's water trap to check for blockages, ensuring the connection has an inner diameter of at least 14 mm.
Why won't my Pelgrim GVWC270L door close?
If you cannot close the door of your Pelgrim dishwasher, ensure that the baskets are correctly positioned horizontally and that dishes are not blocking the baskets from sliding properly into place. If the door lock does not click into place, open the door, press and hold Automatic door opening until the display counts down, wait until the countdown ends (60 seconds), then close the door and check that the door lock clicks into place.
What to do if my Pelgrim Dishwasher is not drying dishes enough?
If your dishes are not drying enough in your Pelgrim dishwasher, activate the Automatic door opening option. Make sure that you fully load the dishwasher. Top up with rinse aid or increase the rinse aid dosage setting. If you are using all-in-one detergent with insufficient drying effect while the TAB setting is activated, switch to separate detergents, deactivate the TAB setting, and top up with salt and separate rinse aid.
Why won't my Pelgrim Dishwasher start?
If your Pelgrim dishwasher does not start, ensure that you have pressed the start button, and the display should start counting down. Check that the door is properly closed and that the door lock has clicked into place. If you opened the dishwasher mid-cycle, close the door and wait for the program to continue. If the Delayed start option is selected, press and hold the relevant button for three seconds to cancel it. Also, check if the plug is correctly inserted into the wall socket and if a fuse or circuit breaker has been tripped.
How to fix F12 error on Pelgrim Dishwasher?
To fix the F12 error on your Pelgrim dishwasher, first check that the water tap is turned on. Then, inspect the outer filter on the inlet hose to ensure it is not blocked.
How to fix F67 error on Pelgrim GVWC270L Dishwasher?
To fix the F67 error on your Pelgrim dishwasher, first check that the water tap is turned on. Then, inspect the outer filter on the inlet hose to ensure it is not blocked.
How to fix F52 error on Pelgrim Dishwasher?
To fix the F52 error on your Pelgrim dishwasher, clean the coarse and fine filters. Also, check that the outer filter on the inlet hose is not blocked.
Why does my Pelgrim Dishwasher have a bad odour?
A bad odor in your Pelgrim dishwasher is likely due to dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner.
General| Type | Freestanding |
|---|---|
| Noise level | 49 dB |
| Drying Class | A |
| Width | 60 cm |
| Height | 85 cm |
| Depth | 60 cm |
To Next Page
