What to do if water remains in my Pelgrim GVWC290L/P03 Dishwasher?
If water remains in your Pelgrim dishwasher, it could be due to several reasons: * The filters might be clogged, so clean the coarse and fine filters. * The filters might not be fitted correctly, so check their placement. * There might be debris in the drainage pump, so clean the drainage pump.
What to do if water remains in Pelgrim Dishwasher?
If water remains in your Pelgrim dishwasher, try the following: * Clean the coarse and fine filters. * Ensure the filters are correctly fitted. * Clean any debris from the drainage pump. * Check that the yellow drainage pump stop is in place. * Make sure the drainage hose isn't kinked or has sharp bends. * Check for blockages in the drainage hose connection to the sink unit, ensuring it has an inner diameter of at least 14 mm.
How to fix Pelgrim GVWC290L/P03 Dishwasher if the dishes are not dry enough?
If your Pelgrim dishwasher leaves dishes not dry enough, consider the following: * Activate the Combi drying option. * Ensure the dishwasher is fully loaded. * Top up the rinse aid or increase its dosage setting. * If using all-in-one detergents with the TAB setting activated, switch detergents or deactivate the TAB setting and add salt and separate rinse aid.
What to do if my Pelgrim GVWC290L/P03 Dishwasher has some foodstuffs causing spots on stainless steel?
If some foodstuffs are causing spots on the stainless steel in your Pelgrim dishwasher, rinse off these types of foodstuffs if not starting the dishwasher immediately. Consider using 1h 65° with the Speed wash option.
What to do if my Pelgrim Dishwasher cannot access your wireless network?
Check that the router is connected to the internet. Make sure your wireless network is using 2.4 GHz and is visible. Try moving the router closer to the dishwasher if the signal is too weak.
What to do if my Pelgrim GVWC290L/P03 has a kink in drainage hose?
If your Pelgrim dishwasher has a kink in the drainage hose, check that the hose is free from kinks and sharp bends.
How to fix F10 error on Pelgrim GVWC290L/P03 Dishwasher?
To fix F10 error on your Pelgrim dishwasher caused by overfilling water, unblock the drainage pump.
What to do if my Pelgrim Dishwasher smartphone/tablet is not connected to your wireless network?
Check that the router is connected to the internet and that your smartphone/tablet is connected to your wireless network.
What to do if the dishwasher is not fully loaded in my Pelgrim GVWC290L/P03 Dishwasher?
If the dishwasher is not fully loaded in your Pelgrim dishwasher, fully load the dishwasher.
Why my Pelgrim GVWC290L/P03 Dishwasher does not start?
If your Pelgrim dishwasher isn't starting, there are several potential causes: * Ensure the start button has been pressed, and the display is counting down. * Verify the door is completely closed. * If you opened the dishwasher mid-cycle, close the door and wait for the program to resume. * Check that the door lock clicks into place; if not, open the door, press and hold the Combi drying button until the display counts down, then close the door again. * If the Delayed start option is active, press and hold the button for three seconds to cancel it. * Confirm that the plug is securely in the wall socket. * Check for tripped fuses or circuit breakers.
General| Type | Freestanding |
|---|---|
| Number of programs | 5 |
| Noise level | 49 dB |
| Number of place settings | 13 |
| Energy Efficiency Class | A++ |
| Capacity | 13 place settings |
| Annual Water Consumption | 2520 L |
| Drying Class | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Child Lock | No |
| Dimensions (HxWxD) | 85 x 60 x 60 cm |
To Next Page