To Next Page
B
Bethany CookSep 3, 2025
How to fix F40 error on Pelgrim Dishwasher?
- SSydney ComptonSep 4, 2025
To fix the F40 error on your Pelgrim dishwasher, turn off the water tap.
How to fix F40 error on Pelgrim Dishwasher?
To fix the F40 error on your Pelgrim dishwasher, turn off the water tap.
Why are my dishes not clean in my Pelgrim Dishwasher?
There are several reasons why your dishes might not be clean. The spray arms may be blocked by dishes, or the spray arm holes or bearings could be blocked, requiring cleaning. You might be using an unsuitable dishwashing program; try a high-temperature program like Intensive 70° for greasy dishes. Incorrect detergent dosage, old detergent, or dishes loaded incorrectly can also cause this problem. Make sure not to cover dishes with large bowls and avoid placing tall glasses in the corners. Glasses and cups should be placed to sit steady. Also, check if the filters are clogged or not fitted correctly, and ensure the yellow drainage pump stop is in place.
Why won't my Pelgrim GVWC270L door close?
If you cannot close the door of your Pelgrim dishwasher, ensure that the baskets are correctly positioned horizontally and that dishes are not blocking the baskets from sliding properly into place. If the door lock does not click into place, open the door, press and hold Automatic door opening until the display counts down, wait until the countdown ends (60 seconds), then close the door and check that the door lock clicks into place.
What to do if my Pelgrim Dishwasher is not drying dishes enough?
If your dishes are not drying enough in your Pelgrim dishwasher, activate the Automatic door opening option. Make sure that you fully load the dishwasher. Top up with rinse aid or increase the rinse aid dosage setting. If you are using all-in-one detergent with insufficient drying effect while the TAB setting is activated, switch to separate detergents, deactivate the TAB setting, and top up with salt and separate rinse aid.
Why won't my Pelgrim Dishwasher start?
If your Pelgrim dishwasher does not start, ensure that you have pressed the start button, and the display should start counting down. Check that the door is properly closed and that the door lock has clicked into place. If you opened the dishwasher mid-cycle, close the door and wait for the program to continue. If the Delayed start option is selected, press and hold the relevant button for three seconds to cancel it. Also, check if the plug is correctly inserted into the wall socket and if a fuse or circuit breaker has been tripped.
How to fix F12 error on Pelgrim Dishwasher?
To fix the F12 error on your Pelgrim dishwasher, first check that the water tap is turned on. Then, inspect the outer filter on the inlet hose to ensure it is not blocked.
How to fix F67 error on Pelgrim GVWC270L Dishwasher?
To fix the F67 error on your Pelgrim dishwasher, first check that the water tap is turned on. Then, inspect the outer filter on the inlet hose to ensure it is not blocked.
How to fix F52 error on Pelgrim Dishwasher?
To fix the F52 error on your Pelgrim dishwasher, clean the coarse and fine filters. Also, check that the outer filter on the inlet hose is not blocked.
Why does my Pelgrim Dishwasher have a bad odour?
A bad odor in your Pelgrim dishwasher is likely due to dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner.
Why does my Pelgrim GVWC270L have grease deposits?
Grease deposits in your Pelgrim dishwasher are often caused by prolonged use of low temperature programs. Select a program with a high temperature to dissolve grease on very dirty dishes, such as Intensive 70°.
General| Type | Freestanding |
|---|---|
| Noise level | 49 dB |
| Drying Class | A |
| Width | 60 cm |
| Height | 85 cm |
| Depth | 60 cm |
