Pentair Aurora PVM Series

Questions and Answers

B
billy44Aug 13, 2025
What to do if Pentair Aurora PVM motor does not run when started?
- M
  Mark RamirezAug 13, 2025
  If the Pentair Water Pump motor doesn't start, there could be several reasons: * A power failure: Check the power supply. * Blown fuses: Replace any blown fuses. * The motor starter overload has tripped: Reset the motor starter overload. * Faulty main contacts or coil in the motor starter: Inspect and repair the motor starter. * Defective control circuit fuses: Replace them. * A defective motor: Replace the motor.
M
Melissa WalkerAug 17, 2025
What to do if Pentair Water Pump motor starter overload trips out immediately?
- J
  Jocelyn ThomasAug 17, 2025
  If the motor starter overload trips out immediately after switching on the power supply, consider the following possible causes: 1. A blown fuse: Replace the blown fuse. 2. Faulty contacts in the motor overload relay: Check and replace the faulty contacts. 3. Loose or faulty cable connections: Inspect and tighten the cable connections. 4. Defective motor winding: Test and replace the defective motor winding. 5. Mechanical blockage in the pump: Clear the mechanical blockage. 6. Overload setting is too low: Adjust the overload setting.
P
Pamela WilsonAug 20, 2025
Why does my Pentair Water Pump run but gives no water?
- J
  Jason RamirezAug 20, 2025
  If your Pentair Water Pump runs but doesn't pump water, the issue could be: * A blockage in the suction pipe or pump: Clear any blockages. * A blocked foot or nonreturn valve: Inspect and clear the blocked valve. * Leakage in the suction pipe: Repair the leakage. * Air in the suction pipe or pump: Bleed air from the system. * The motor rotating in the wrong direction: Rewire the motor for correct rotation.
B
Barry HaysAug 25, 2025
Why does Pentair Aurora PVM motor starter overload trip out occasionally?
- M
  Maurice PerezAug 25, 2025
  The motor starter overload may be tripping occasionally because: * The overload setting is too low: Adjust the overload setting. * There's low voltage at peak times: Ensure a stable voltage supply.
H
Heidi FergusonAug 28, 2025
What to do if there is leakage from the shaft seal of Pentair Aurora PVM Water Pump?
- A
  aliciawatsonAug 28, 2025
  If there is leakage from the shaft seal, it could be due to: * Incorrect pump shaft position: Adjust the pump shaft position. * A defective shaft seal: Replace the defective shaft seal.
C
Cindy ChambersSep 1, 2025
Why is Pentair Aurora PVM capacity not constant?
- D
  Derrick CraigSep 1, 2025
  If your Pentair Water Pump's capacity fluctuates, it could be due to: * Pump inlet pressure being too low: Increase the pump inlet pressure. * A partial blockage in the suction pipe or pump: Clear any blockages. * The pump sucking air: Check for air leaks.
S
Sean GrantSep 4, 2025
Why does Pentair Aurora PVM run backward when switched off?
- J
  Jonathan OlsonSep 4, 2025
  If your Pentair Water Pump runs backward after being switched off, consider these potential causes: * Leakage in the suction pipe: Repair any leaks. * A defective foot or nonreturn valve: Replace the defective valve. * A foot valve blocked in an open or partly open position: Clear the blockage. * A nonreturn valve leaking or blocked open: Inspect and repair the valve. * A defective discharge valve: Replace the defective valve.
R
Randy WaltersSep 8, 2025
How to fix noise in Pentair Aurora PVM?
- J
  Jessica PetersenSep 8, 2025
  If your Pentair Water Pump is making unusual noises, the cause might be: * Cavitation: Mitigate cavitation. * Increased frictional resistance due to incorrect shaft position: Ensure the pump rotates freely.