Pentair EASYTOUCH PL4 Appliance Upgrade Guide

v
Note: Refer to page 3 where (parts index number) is shown
EasyTouch/IntelliTouch Control System Legacy Upgrade Kits Installation Instructions
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
FCC Regulatory Safety Notice
FCC non-modification statement:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Exposure requirements:
Notice for High Power Wireless Link (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: In order to comply with FCC/ISED RF Exposure requirements, a minimum separation distance of 8 in (20
cm) must be maintained between the equipment and all persons during normal operation.
Exigences de la FCC en matière d’exposition aux fréquences radio:
Remarquer: pour lien sans fil haute puissance (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: Afin de respecter les exigences d’exposition RF de la FCC / ISED, une distance minimale de 20 cm doit être
respectée entre l’appareil et toutes les personnes en fonctionnement normal.
Canada - Innovation, Science and Economic Development (ISED)
(ISED: 21176-QTSHPWETH): The Control System and the High Power Wireless (HPW) Link complies with RSS210 of ISED Canada (2019).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Innovation, Science and Economic Development (ISED) Exempt RSSs. Operation is subject to the
following: (1) This device may not cause interference; and (2) This device must accept interference that may cause undesired operation of the
device.
FCC Regulatory Notice - 47 CFR Part 15, Subpart C
Instruction to User: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does
cause harmful interference to radio or television reception, which can be determined by switching the device off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Regulatory Notice – RSS210:
Instruction To User: This device complies with RSS210 of Innovation, Science and Economic Development Canada (ISED). Under ISED
regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Innovation, Science and Economic
Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Conformément à la réglementation d’Innovation, Sciences et Developpment Economique Canada (ISED), le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par ISED. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. Le présent appareil est conforme
aux CNR d’Innovation, Sciences et Developpment Economique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Le dispositif est conforme à la licence Innovation, Science and Economic Development (ISED) Canada. Le fonctionnement est soumis à la suivante.
(1) Ce ne doit pas provoquer d’interférences ; et (2) Cet appareil doit accepter les interférences qui peuvent causer un mauvais fonctionnement de
l’appareil.
Cet appareil numérique de classe B est conforme à la norme canadienne ISDE (RSP-100, section 2.1) et Terminal Equipment Registrations (DC-
01, Section 3.). Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le terme «ISED» précédant le numéro de
certification / d’enregistrement signifie uniquement que les spécifications techniques relatives à l’innovation, à la science et au développement
économique ont été respectées.

Pentair EASYTOUCH PL4 Specifications

General

Brand	Pentair
Model	EASYTOUCH PL4
Category	Control Systems
Language	English