Pentair REBEL 2 - CLEANER ADJUSTMENTS & OPERATION; Hose Length Determination; Eyeball Diverter Positions

3
REBEL
®
2 Automatic Vacuum Pool Cleaner Owner’s Manual
REBEL
®
2 Automatic Vacuum Pool Cleaner Owner’s Manual
2 3
Male Hose End
Female Hose End
Hose Assembly
For best results and to maintain proper operation, use only
original Pentair parts and hoses.
1. To connect the hose sections, wet the ends in the
pool water, then twist and push the female ends
onto the male ends.
2. Connect the leader hose to the cleaner swivel. See
Figure 3.
Note: The leader hose is 50 centimeters in length
and shorter than the other sections included in the
hose set. The leader hose is also marked with a red
sticker. Failure to use this leader hose section will
hinder cleaner performance
3. The hose should reach from where the cleaner is
connected to the farthest point of the pool, plus one
section and the leader hose.
4. Install the hose oat onto the second length of
hose. The oat should be placed 63.5cm above the
cleaner. See Figure 4.
5. Make sure that all connections are snug.
6. The overall length of hose needed will be
determined by the distance from the point at which
you attach the hose to the suction port to the
furthest point in the pool, plus one length and the
leader hose. Refer to Figure 5.
Figure 2
Figure 3
The Rebel
®
2 Automatic vacuum pool cleaner body is
shipped as one piece, making cleaner assembly a simple
and quick process.
INSTALLING THE CLEANER
ASSEMBLING THE CLEANER
Figure 4
Figure 5
23 in
(63.5cm)
Leader
Hose
Swivel
Assembly
3
REBEL™ Suction Side Pool Cleaner Installation and User’s Guide
INSTALLING THE CLEANER
Different brands of skimmer box
Attach; Skimmer Adaptor Cuff into skimmer plate, then attach Adjustable Regulator
Valve & 90 Degree Elbow to skimmer plate. Then connect one end of submerged hose
into the 90 Degree Elbow.
90 Degree Elbow
Adjustable Regulator Valve
Skimmer Adaptor Cuff
Waterco Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Poolrite Skimmer Box
Screw in the threaded
adaptor from the bottom
of the skimmer plate
Quiptron Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Standard Installation
1. Turn the pool pump off.
2. Close the main drain.
3. Connect the hose to the skimmer vac plate as per below instructions:
Different brands of skimmer box
Attach; Skimmer adaptor cuff into skimmer plate, then attach Adjustable regulator valve and 90 Degree elbow to
skimmer plate. Then connect one end of submerged hose into the 90 Degree elbow.
Waterco Skimmer Box
Screw in the threaded adaptor from
the top of the skimmer plate.
Poolrite Skimmer Box
Screw in the threaded adaptor from
the bottom of the skimmer plate.
Quiptron Skimmer Box
Screw in the threaded adaptor from
the top of the skimmer plate.
90 Degree Elbow
Adjustable Regulator Valve
Skimmer Adaptor Cuff
3
REBEL™ Suction Side Pool Cleaner Installation and User’s Guide
INSTALLING THE CLEANER
Different brands of skimmer box
Attach; Skimmer Adaptor Cuff into skimmer plate, then attach Adjustable Regulator
Valve & 90 Degree Elbow to skimmer plate. Then connect one end of submerged hose
into the 90 Degree Elbow.
90 Degree Elbow
Adjustable Regulator Valve
Skimmer Adaptor Cuff
Waterco Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Poolrite Skimmer Box
Screw in the threaded
adaptor from the bottom
of the skimmer plate
Quiptron Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Standard Installation
1. Turn the pool pump off.
2. Close the main drain.
3. Connect the hose to the skimmer vac plate as per below instructions:
3
REBEL™ Suction Side Pool Cleaner Installation and User’s Guide
INSTALLING THE CLEANER
Different brands of skimmer box
Attach; Skimmer Adaptor Cuff into skimmer plate, then attach Adjustable Regulator
Valve & 90 Degree Elbow to skimmer plate. Then connect one end of submerged hose
into the 90 Degree Elbow.
90 Degree Elbow
Adjustable Regulator Valve
Skimmer Adaptor Cuff
Waterco Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Poolrite Skimmer Box
Screw in the threaded
adaptor from the bottom
of the skimmer plate
Quiptron Skimmer Box
Screw in the threaded
adaptor from the top of
the skimmer plate
Standard Installation
1. Turn the pool pump off.
2. Close the main drain.
3. Connect the hose to the skimmer vac plate as per below instructions:
Standard Installation
1. Turn the pool pump off.
2. Close the main drain.
3. Connect the hose to the skimmer vac plate as per below instructions: