EasyManua.ls Logo

Pentair STA-RITE DS3 Series - User Manual

Pentair STA-RITE DS3 Series
13 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
pentair.com/sta-rite
S536 (11-25-19) © 2019 Pentair. All Rights Reserved.
INSTALLATION AND
OPERATION MANUAL
SELF-PRIMING CENTRIFUGAL PUMP
DS3 SERIES
3621 0714 ASB

Table of Contents

Other manuals for Pentair STA-RITE DS3 Series

Preview: Owner's Manual
Owner's Manual12 pages

Questions and Answers

  • E
    ericavaldezJul 27, 2025
    What to do if my Pentair Water Pump motor will not run?
    • T
      Travis JonesJul 27, 2025
      If your Pentair Water Pump motor isn't running, there are several potential causes. First, ensure the disconnect switch is turned on. Next, check the fuse and replace it if it's blown. A defective starting switch could also be the culprit, so consider replacing it. Lastly, inspect the wiring at the motor for looseness, disconnections, or incorrect wiring. Refer to the wiring instructions and tighten all connections. Be cautious of capacitor voltage and discharge the capacitor with an insulated screwdriver if necessary. If unsure, consult a qualified electrician.
  • A
    Aaron MorrisAug 10, 2025
    Why does my Pentair STA-RITE DS3 Water Pump motor run hot and the overload keep kicking off?
    • L
      Leonard ZamoraAug 10, 2025
      If your Pentair Water Pump motor runs hot and the overload trips, it could be due to incorrect wiring. Refer to the wiring instructions to ensure it's properly connected. Another potential cause is low voltage. Check with your power company and consider installing heavier wiring if the current wire size is too small.
  • S
    Samuel HillAug 18, 2025
    How to fix a Pentair Water Pump that does not deliver water to full capacity?
    • V
      Victor BurgessAug 18, 2025
      If your Pentair Water Pump isn't delivering water to its full capacity, a leaking foot valve could be causing a loss of priming, so replace the foot valve. If the water level in the well is more than 25 feet below the pump's suction point, you might need a deep well jet pump. Corroded or limed steel piping (if used) can cause excess friction; replace it with plastic pipe where possible, or with new steel pipe. Also, ensure that the offset piping isn't too small; use larger offset piping if needed.
  • N
    Nicholas ScottNov 2, 2025
    Why is my Pentair STA-RITE DS3 motor running but not delivering water?
    • D
      Daniel MatthewsNov 2, 2025
      If your Pentair Water Pump motor is running but not delivering water, first check the prime by unscrewing the priming plug to see if there is water in the priming hole. Then, consider these possibilities: * **For new installations:** Improper priming, air leaks, or a leaking foot valve could be the cause. Re-prime according to instructions, check all suction line connections, and replace the foot valve. * **For installations already in use:** Air leaks or a water level below the pump's suction could be the issue. Check all connections on the suction line and shaft seal. Lower the suction line into the water and re-prime. If the receding water level in the well exceeds the suction lift, a deep well pump is needed. * The impeller may be plugged, so clean it according to the cleaning/r...

Summary

SAFETY

GENERAL SAFETY

General safety precautions for pump operation and maintenance.

CALIFORNIA PROPOSITION 65 WARNING

Warning about chemicals linked to cancer and reproductive harm.

ELECTRICAL SAFETY

Electrical safety rules, including grounding and wiring best practices.

INSTALLATION

PRIOR TO PUMP INSTALLATION

Pre-installation checks and steps for pump setup.

WELL PIPE INSTALLATION

Guidance for installing pump piping in various well types.

CASED WELL INSTALLATION

Specific installation steps for cased wells.

DUG WELL INSTALLATION

Installation procedures for dug wells.

DRIVEN POINT INSTALLATION

Installation procedures for driven point wells.

INSTALLATION

DISCHARGE PIPE SIZES

Selecting correct discharge pipe sizes based on distance.

LAWN SPRINKLING APPLICATION

Pump suitability and use for lawn sprinkling systems.

PUMP INSTALLATION

Physical mounting and setup procedures for the pump.

ELECTRICAL

MOTOR VOLTAGE CONFIGURATION

Adjusting motor voltage settings for dual-voltage units.

POWER SUPPLY CONNECTIONS

Safe connection of the pump to the electrical power source.

ELECTRICAL

WIRING CHART - RECOMMENDED WIRE AND FUSE SIZES

Table of wire sizes and fuse ratings for different models and distances.

OPERATIONS;MAINTENANCE

PRIMING THE PUMP

Step-by-step guide to properly prime the pump before operation.

MAINTENANCE

CLEANING;REPLACING IMPELLER

Procedures for cleaning or replacing the pump impeller.

REMOVING OLD SEAL

Instructions for safely removing the old shaft seal.

MAINTENANCE

INSTALLING NEW SEAL

Detailed steps for installing a new shaft seal correctly.

PUMP REASSEMBLY

Procedures for reassembling the pump after maintenance.

TROUBLESHOOTING

MOTOR WILL NOT RUN

Diagnosing and resolving issues when the motor fails to start.

MOTOR RUNS HOT AND OVERLOAD KICKS OFF

Troubleshooting an overheating motor and overload trips.

MOTOR RUNS BUT NO WATER IS DELIVERED

Solutions for when the pump runs but no water is pumped.

PUMP DOES NOT DELIVER WATER TO FULL CAPACITY

Addressing reduced water flow or pressure from the pump.

Pentair STA-RITE DS3 Series Specifications

General IconGeneral
BrandPentair
ModelSTA-RITE DS3 Series
CategoryWater Pump
LanguageEnglish

Related product manuals