EasyManuals Logo

Performance Tool W1626 User Manual

Performance Tool W1626
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
UNPACKING AND INSPECTION
After opening the carton, unpack your new product and related parts and accessories. Please
inspect it carefully for any damage that may have occurred during transit. Please check it against
the photograph on carton. If any parts are missing, please call customer service at 1-800-426-1262
between 6 a.m. and 5 p.m. Pacific time.
WARNING: DO NOT operate this product if damaged during shipment, handling or misuse.
Do not operate the product until the parts have been replaced or the fault rectified. Failure to do
so may result in serious personal injury or property damage. All damaged parts must be repaired
or replaced as needed prior to operating this product. Check to see that all nuts, bolts and fittings
are secure before putting this product into service.
If you have any questions, or require assistance with damaged or missing parts, please contact
our customer service department at 1-800-426-1262. Please have the serial number, model
number, and date of purchase available for reference when calling.
1. Study, understand and follow all instructions
before operating this device.
2. DO NOT exceed rated capacity. Overloading
can cause damage to or failure of this product.
3. Use only on hard, level surface capable of
sustaining the load. Use of jack on other than
hard level surfaces can result in jack instability
and possible loss of load.
4. Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
Ensure that no personnel pass underneath
load until load is securely supported by jack
stands.
5. DO NOT adjust safety valves.
6. Wear ANSI approved safety goggles and
heavy duty work gloves during use.
7. Keep clear of load while lifting and lowering.
8. Lower load slowly.
9. DO NOT use for aircraft purposes.
10. Apply parking brake and chock tires before
lifting vehicle.
11. Lift vehicle only at vehicle manufacturer
recommended lift locations.
12. Inspect before every use; do not use if parts
are loose or damaged.
13. Do not alter this product in any way.
14. Keep your work area clean and well lit.
Cluttered work areas invite accidents.
15. Keep bystanders, children, and visitors away
while operating this product. Distractions can
cause you to lose control.
16. Stay alert. Watch what you are doing, and use
common sense when operating this product.
Do not use this product while tired or under
theinuenceofdrugs,alcoholormedication.
17. Store idle jacks out of reach of children and
other untrained persons. Jacks are dangerous
in the hands of untrained users.
18. Tool/equipment service must be performed
onlybyqualiedrepairpersonnel.Serviceor
maintenanceperformedbyunqualied
personnel could result in a risk of injury.
19. When servicing this product, use only
identical replacement parts - refer to attached,
product-specicpartslistanddiagram.Follow
instructions in the Care & Maintenance
section of this manual. Use of unauthorized
parts or failure to follow maintenance
instructions may create a risk of injury and
may void any applicable warranty.
20. Maintain labels and nameplates on this
product. These carry important information. If
unreadable or missing, contact Performance
Tool for a replacement.
21.Beforeuse,readmanufacturer’sinstruction
manual for the vehicle (or object) you will lift.
22. When lifting only one wheel, support the load
immediately with one jack stand (not included)
placed under the side of the vehicle being
lifted. Align the saddle of the jack stand
directlyunderthevehicle’sframeor
recommended lifting point.
23. When lifting the entire front end or rear end
of a vehicle, support the load immediately
with two jack stands. Align the saddles of the
jackstandsdirectlyunderthevehicle’sframe
or recommended lifting points. Also, adjust the
jack stands to the same height.
24. Do not work under the vehicle without properly
supporting the vehicle with jack stands.
25.Avoiddangerousoncomingtrafc.Usethe
Jack as far away from the roadside as possible.
26. Industrial applications must follow OSHA
requirements.
27. Do not allow anyone inside the vehicle while
using the Jack. Keep all bystanders a safe
distance away from the vehicle.
28. Do not support both ends of the vehicle at the
same time.
29. Before lowering the jack, remove all tools and
equipment from under the vehicle.
30. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that
may occur. The operator must understand that
common sense and caution are factors, which
cannot be built into this product, but must be
supplied by the operator.
WARNING: This is a lifting device only. Load must be supported immediately by jack stands.
IMPORTANT SAFETY INFORMATION
3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Performance Tool W1626 and is the answer not in the manual?

Performance Tool W1626 Specifications

General IconGeneral
BrandPerformance Tool
ModelW1626
CategoryJacks
LanguageEnglish

Related product manuals