Philips Allegiant LTC 8800 Series - Keyboard Hookup; Satellite Configuration Installations

23
If a TC8802 monitor expansion bay is supplied, each
camera that is connected to the TC8801 main CPU
bay must also be connected to the same numbered
input on the monitor expansion bay.
TC8802 Video Connections
With the TC8802 monitor expansion bay, ribbon
cable connectors are provided for the video inputs.
Video is to be looped from the main bay into the
expansion bay through 16 TC8809 ribbon cables.
Connect all TC8809 ribbon cables from the
appropriate "VIDEO" ribbon cable connector on the
main bay to the corresponding "VIDEO" ribbon cable
connector on the monitor expansion bay. The ribbon
cable connectors contain a small “key”
protrusion formed into one side of the connector
to assure proper placement into the mating
connectors. Be careful not to force the cables
into the mating connectors backwards. The DIP
switches on the VIM cards installed in the main bay
should be turned OFF. This will make the main bay
inputs non-terminated, and the expansion bay will
provide the termination for the video inputs.
KEYBOARD
VIDEO IN
1
3
5
7
2
4
6
8
CONSOLE
ALARM
PRINTER
SDA
COMM PORT 1
COMM PORT 2
1
3
VIDEO
OUT
2
4
9
101112
17
18
1920
25
2627
28
33
343536
41424344
49
5051
52
57
5860
65
66
6768
73
7475
76
81
828384
89
90
9293
94
96
85
868788
77
7879
80
69
70
7172
61
6264
53
5455
56
45464748
37
383940
29
3031
32
21
22
2324
13
141516
5
67
8
1
SYNC
IN
32 25 18 6
7
8
9
10
11
122431
2330
2229
2128
20
27
19
26
5
4
3
2
17
16
15
14
13
LOOP 1-16
LOOP 17-32
LOOP 33-48
LOOP 49-64
LOOP 65-80
LOOP 81-96
INPUT 97-112
LOOP 97-112
INPUT 113-128
LOOP 113-128
INPUT 129-144
LOOP 129-144
INPUT 145-160
LOOP 145-160
LOOP 241-256
INPUT 241-256
INPUT 225-240
LOOP 225-240
LOOP 209-224
INPUT 209-224
LOOP 193-208
INPUT 193-208
LOOP 177-192
INPUT 177-192
LOOP 161-176
INPUT 161-176
59
9195
63
KEYBOARD
VIDEO IN
1
3
5
7
2
4
6
8
CONSOLE
COMM PORT 2
13
VIDEO
OUT
2
4
9
1011
12
17181920
25
26
2728
33
3435
36
41424344
49
50
5152
57
58
60
65666768
73
74
7576
81
828384
899092939496
85
868788
77
78
7980
69707172
61
62
64
53
54
5556
45464748
37
3839
40
29
30
3132
21222324
13
1415
16
5
6
78
1
SYNC
IN
32 25 18 6
7
8
9
10
11
122431
2330
2229
2128
20
27
19
26
5
4
3
2
17
16
15
14
13
LOOP 1-16
LOOP 17-32
LOOP 33-48
LOOP 49-64
LOOP 65-80
LOOP 81-96
INPUT 97-112
LOOP 97-112
INPUT 113-128
LOOP 113-128
INPUT 129-144
LOOP 129-144
INPUT 145-160
LOOP 145-160
LOOP 241-256
INPUT 241-256
INPUT 225-240
LOOP 225-240
LOOP 209-224
INPUT 209-224
LOOP 193-208
INPUT 193-208
LOOP 177-192
INPUT 177-192
LOOP 161-176
INPUT 161-176
59
9195
63
TC8801
TC8802
TC8809
Ribbon
Cables
Typical TC8809 Connections
TC8802 Data Connections
The TC8802 is supplied with a TC8716C2 data
communication interconnect cable with two
connectors spaced about 3 feet apart. Install the
TC8716C2 cable between the Comm1 port on the
TC8801 Main CPU bay, and the Comm1 port on the
TC8802 monitor expansion bay.
Keyboard Hookup
Connect a maximum of 8 system keyboards to any
of the 8 keyboard ports (modular phone type jacks)
provided on the rear of the TC8x01 Main CPU bay,
but be sure to at least connect a keyboard to port #1.
The TC8500 is limited to these 8 keyboards. Other
systems may accommodate 16 or 32 keyboards
using TC8714A and TC8715A series keyboard port
expander accessory units.
Additional keyboards may also be used with a
TC8802A Series Monitor Expansion Bay. Connect
the keyboards the same way as with the TC8801A
Series Main Bay. DIP switches 2 and 3 of S101 on
the Data Receiver module in the Monitor Expansion
Bay must now be set according to the table below.
Desired Keyboard Numbers
On Monitor Expansion Bay
Keyboards Switch 2 Switch 3
None OFF OFF
9 to 16 OFF ON (recommended setting)
17 to 24 ON OFF
25 to 32 ON ON
Each keyboard is supplied with a 10-foot cable for
local hookups. The TC8x01 can provide power to
keyboards up to 100 feet away using the optional
TC8557HL hookup cable. For distances of up to
5000 feet, the optional TC8557HR hookup kit is
required, which is supplied with a remote power pack
and requires user-supplied shielded twisted pair
(Belden 9841 or equivalent) for communication.
Satellite Configuration Installations
Due to the many variations possible, only general
guidelines can be covered for installing satellite
systems. Refer to the appendix section of this
manual, the TC8850 Graphical User Interface
Software manual or the TC8x59 Master Control
Software package manual for additional
configuration and programming information on
satellite systems.
Central
Control
Station
Satellite
System
#1
Satellite
System
#2
Satellite
System
#3
Satellite
System
#4
Satellite
System
#5
Satellite
System
#6
Video and
Data Links
S9507002AE
Satellite Concept Configuration