INSTRUCTIONS FOR USE
3-4
PCS 104 414
Finding a passage within a track
1. Press and hold down SEARCH ∞ or §.
™The CD is played at high speed and low volume.
2. When you recognize the passage you want,
release SEARCH ∞ or §.
– Normal playback continues.
Note: During a CD programme or if SHUFFLE/ REPEAT active,
searching is only possible within a track.
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes before or during
playback. The play modes can also be combined with PROGRAM.
SHUFFLE - tracks of the entire CD/ programme are played in
random order
SHUFFLE and REPEAT ALL - to r
epeat the entire CD/ programme
continuously in random order
REPEAT ALL - to repeat the entire CD/ programme
REPEAT - to play the cur
rent track continuously
1. To select your play mode, press the CD MODE key (or
SHUFFLE or REPEAT on the remote control) befor
e or during
playback until the display shows the desired function.
2. Press PLAY•PAUSE 2;to start playback if in the STOP position.
3. To return to nor
mal playback, press the
CD MODE key or the
respective SHUFFLE or REPEAT key until the various SHUFFLE
/ REPEAT modes are no longer displayed.
– You can also press STOP 9 to cancel your play mode.
Programming track numbers
Pr
ogramme in the STOP position to select and store your CD tracks
in the desired sequence. If you like, stor
e any track more than
once. Up to 20 tracks can be stored in the memory
.
1. Use the SEARCH ∞ or § on the set (on the r
emote control
¡
or ™), to select your desired track number
.
2. Press PROGRAM.
™Display: PROGRAM and the selected track number.
appears briefly.
™If you attempt to programme without first selecting a track
number, is shown.
3. Repeat steps 1-2 to select and store all desir
ed tracks.
™ is displayed if you attempt to programme more than
20 tracks.
4. To star
t playback of your CD programme, pr
ess
PLAY•PAUSE 2;.
Reviewing the programme
In the
STOP position, pr
ess and hold down
PROGRAM for a while
until the display shows all your stored track numbers in sequence.
Erasing a programme
You can erase the programme by:
– pressing STOP 9 once in the STOP position or twice during
playback. The display shows ' ' briefly.
– pressing the CD door open;
– switching to TUNER/TAPE source.
CD player and CD handling
• If the CD player cannot read CDs correctly, use a commonly
available cleaning CD to clean the lens before taking the set to
repair. Other cleaning methods may destroy the lens.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can cause
condensation to cloud over on the lens of your CD player.
Playing a CD is then not possible. Do not attempt to clean the
lens but leave the set in a warm envir
onment until the
moisture evaporates.
•
Always keep the CD compartment closed to avoid dust on
the lens.
• To take a CD out of its box, press the centre spindle while
lifting the CD. Always pick up the CD by the edge and r
eturn
the CD to its box after use to avoid scratching and dust.
• To clean the CD, wipe in a straight line from the centre
towar
ds the edge using a soft, lint-free cloth. Do not use
cleaning agents as they may damage the disc.
• Never write on a CD or attach any stickers to it.
PLA
YING A CASSETTE
1. Select TAPE source.
™The display shows tAPE throughout tape operation.
2. Press STOP•OPEN 9/ to open the cassette door.
3. Insert a recorded cassette and close the cassette door
.
4. Press PLAY 1 to start playback.
5. To interr
upt playback, press
PAUSE ;. To resume, pr
ess the
key again.
8. By pressing SEARCH 5 or 6 on the set,
fast winding of the
tape is possible in both directions.
9. To stop the tape, pr
ess
STOP•OPEN 9/.
– The keys ar
e automatically released at the end of the tape
and the tAPE indication goes out, except if PAUSE ; has
been activated.
To Next Page
Loading...
