PCS 107 277
3-5
INSTRUCTION FOR USE
GENERAL INFORMATION ON RECORDING
• Recording is permissible insofar as copyright or other rights of
third parties are not infringed.
• This deck is not suitable for recording on CHROME (IEC II) or
METAL (IEC IV) type cassettes. For recording, use NORMAL type
cassettes (IEC I) on which the tabs have not yet been broken.
•
The best recording level is set automatically.
Altering the
VOLUME, INCREDIBLE SURROUND, ULTRABASS or ULTRA
HIGH CLARITY controls will not affect the recording in
progress.
• At the very beginning and end of the tape, no recording will take
place during the 7 seconds when the leader tape passes the
recorder heads.
• To protect a tape from accidental erasure, have the tape in front
of you and break out the left tab.
Recording on this side is no longer possible. If, however, you
wish to record over this side again, cover the tabs with a piece
of adhesive tape.
SYNCHRO START CD RECORDING
1.
Select CD source.
2.
Insert a CD and if desired, programme track numbers.
3.
Press STOP•OPEN 9/ to open the cassette door.
4.
Insert a suitable cassette into the cassette deck and close the
cassette door.
5.
Press RECORD 0 to start recording.
– Playing of the CD programme starts automatically from the
beginning of the programme.
It is not necessary to start the
CD player separately.
To select and record a particular passage within a track
• Press and hold down SEARCH ∞ or §
(
for AZ2035 model only:
or on the remote control ¡ or ™).
• When you recognize the passage you want, release
SEARCH ∞ or §.
• To pause CD playback press PLAY 2; (
for AZ2035 model only:
or on the remote control 2;).
– Recording will begin from this exact point in the track when you
press RECORD 0.
6.
For brief interruptions press PAUSE ;. To resume recording,
press PAUSE ; again.
7.
To stop recording, press STOP•OPEN 9/.
Reviewing the programme
In the STOP position or during playback, press and hold down
PROG for a while until the display shows all your stored track
numbers in sequence.
Erasing a programme
You can erase the programme by:
– pressing STOP 9 twice in the STOP position or during playback.
• scrolls across the display briefly and
PROGRAM
disappears.
– selecting another source: TAPE or TUNER.
CD player and CD handling
• If the CD player cannot read CDs correctly, use a commonly
available cleaning CD to clean the lens before taking the set to
repair. Other cleaning methods may destroy the lens.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can cause
condensation to cloud over on the lens of your CD player. Playing
a CD is then not possible. Do not attempt to clean the lens but
leave the set in a warm environment until the moisture
evaporates.
• Always keep the CD compartment closed to avoid dust on the
lens.
• To take a CD out of its box, press the centre spindle while lifting
the CD. Always pick up the CD by the edge and return the CD to
its box after use to avoid scratching and dust.
• To clean the CD, wipe in a straight line from the centre towards
the edge using a soft, lint-free cloth. Do not use cleaning agents
as they may damage the disc.
• Never write on a CD or attach any stickers to it.
CASSETTE PLAYBACK
1.
Select TAPE source.
™ The display shows throughout tape operation.
2.
Press STOP•OPEN 9/ to open the cassette door.
3.
Insert a recorded cassette and close the cassette door.
4.
Press PLAY 1 to start playback.
5.
To interrupt playback, press PAUSE ;. To resume, press this key
again.
6.
By pressing SEARCH 5 or 6 on the set, fast winding of the
tape is possible in both directions.
7.
To stop the tape, press STOP•OPEN 9/.
– The keys are automatically released at the end of the tape,
except if
PAUSE ;
has been activated.
X
PLA
Y
STOP
CD MODE
¥ ¥ ¥ SEARCH
SEARCH ¥ ¥ ¥
PROG
BAND
PRES
BATT
LOW
FM
To Next Page
Loading...
