English
21
During finalizing the Table of Contents (TOC) is written to the
disc.
Finalizing is a simple procedure, necessary to:
- be able to play recordings on a CD PLAYER,
- avoid further unwanted recordings on a disc,
- avoid erasure of tracks on a CDRW,
- write CD text on a CDR(W).
Auto finalizing
Auto finalizing is possible when using the MAKE CD recording
function.
Manual finalizing
1 Make sure the disc (in the CD recorder deck) is absolutely
free of scratches and dust particles.
2 With the recorder stopped press FINALIZE.
➜ The display shows FINALIZE CD and PRESS
RECORD.
3 Press RECORD.
➜ XX XX FINAL and the approximate finalization time
appears on the display.
The display counts down through the finalization.
On completion, the total number of tracks and the total
time recorded appears on the display.
For CDR(W),
r
changes to
d
on display.
Finalizing will take at least 2 - 4 minutes.
Note:
- During finalization, the CD recorder accepts no operating
commands.
- When a CDR is finalized no more recordings can be added.
For CDRW discs only.
If you want to make more recordings (or erasures of tracks) on a
finalized disc you must unfinalize it first. The Table of Contents
(TOC) will be removed. (This is not possible for CDR discs.)
To unfinalize:
1 With the CD recorder stopped, press REC TYPE or ERASE.
➜ UNFINALIZE and PRESS ENTER will appear on
the display.
2 Press JOG (ENTER).
➜ The disc will now be unfinalized and can be recorded on
again and the Recording or Erasure mode is entered.
3 You can now start recording or erasing. If no further
recording or erasure is required press STOP 9.
Note:
- Unfinalizing will take approximately 1 minute 30 seconds.
- When unfinalizing a CDRW disc with text on it available,
this text will be transferred to the CD recorder memory. It
may occur that the text memory is full. The message
MEMORY FULL
/
FINALIZE CD
will be displayed.
To empty the recorders text memory you have to erase text
from it. This can be done in two ways:
1) Finalize one or more unfinalized discs for wich CD text is
available.
2) Delete text of unfinalized discs with the ‘memory view’
option in the Menu mode.
Unfinalizing CDRW discsFinalizing CDR & CDRW discs
RECORDING
English
20
The CD-SYNC feature enables you to make fast and easy
recordings of a CD. Track increments are automatically
detected from the source material. Track increments cannot
be added manually. In analog source material a silence of 2.7
seconds or more is automatically detected as a track
increment.
Preparing for autostart recording
1 Make sure the disc is absolutely free of scratches and dust
particles.
2 Press EXT(ernal) SOURCE repeatedly until (depending on the
digital connection used):
➜ DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG appears on the
display.
3 With the CD recorder stopped, press REC TYPE four times:
if you wish to record a complete disc or program.
➜ d and
SYNC
start to flash and the display shows REC
EXT DISCand WAIT followed by the track number,
the total remaining time and START SOURCE.
•If input label (DIGITAL I) flashes, the digital connection is
incorrect.
Start autostart recording
1 To start recording, press PLAY on the selected source.
➜ The CD recorder automatically starts to record and d
and
SYNC
lights continuously. The track number and track
time appear on the display.
•If, however, you start the source during a track, CD-SYNC
recording starts at the beginning of the next track or after
2.7 seconds of silence in analog recordings.
•To check the remaining recording time on the CDR(W), press
DISPLAY. (This can also be done during recording.)
•The EASY JOG/ENTER key can be used to adjust the
recording level.
•The recorder stops automatically.
2 To stop recording manually, press STOP on the CD recorder.
➜ UPDATE lights up and
SYNC
and d go out.
•If STOP 9 was pressed within 3 seconds after pressing
PLAY, no recording will take place.
•To interrupt recording, press PAUSE on the CD recorder.
➜ d starts to flash. (Autostart recording is disabled.) To
resume, press RECORD on the CD recorder.
After recording the display will show UPDATE for several
seconds.
Note: Auto track is always active.
Important:
If you want to play the recorded CDR disc on any
regular CD player, it must first be finalized. See
finalizing discs.
Finalized CDRW discs play only on CDRW compatible
CD players.
For recording from CD changers always use
REC EXT
DISC
.
REM
TRACK
REC
TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN
I
I
CD
RW
CHANGER
SYNC MANUAL
RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
REM
TRACK
REC
TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN
I
I
CD
RW
CHANGER
SYNC MANUAL
RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
O
P
E
N
/ C
L
O
S
E
PLA
Y / P
A
U
S
E
STO
P
R
E
C
T
Y
P
E
O
P
E
N
/ C
L
O
S
E
PLA
Y / P
AUSE
S
T
OP
E
X
T
S
O
U
R
C
E
E
R
A
SEF
IN
ALIZ
E
CD
R
R
E
C
O
R
D
To Next Page
Loading...
