What to do if Philips M1019A IntelliVue G5 show -?-, INOP tone, and blinking Setup LED?
If your Philips Gas Analyzer displays '-?-' instead of numerics, emits an INOP tone, and the Setup LED is blinking, this indicates a hardware problem. Check the connection to the monitor. Try switching the Gas Analyzer off and then on again to resolve the issue.
What to do if Philips M1019A IntelliVue G5 show GM OCCLUSION error?
If your Philips Measuring Instruments display 'GM OCCLUSION' and numerics are replaced by '-?-' with an INOP tone, ensure the sample and exhaust lines aren't kinked. Check the airway adapter for water buildup, empty it, and reposition the adapter so the port faces upwards. Consider replacing the sample line, watertrap, or exhaust line.
Why Philips M1019A IntelliVue G5 Measuring Instruments show GM NOT AVAILABLE error?
If your Philips Measuring Instruments display 'GM NOT AVAILABLE' with an INOP tone, it means the Gas Analyzer is either disconnected or switched off. Ensure it is properly connected and powered on.
How to fix Philips Measuring Instruments GM ZERO FAILED error?
If your Philips Measuring Instruments display 'GM ZERO FAILED' and numerics are shown as '-?-', check the exhaust tube for any occlusions or kinking, and replace it if necessary. You can also manually start another zero calibration.
Why is Philips M1019A IntelliVue G5 GM accuracy reduced?
If your Philips gas analyzer displays numerics as '-?-' and the measurement accuracy seems reduced, check that the gas inlet, watertrap, and gas outlet tubing are not occluded.
What does GM COMPONENT MALF mean on Philips M1019A IntelliVue G5?
If your Philips Measuring Instruments display 'GM COMPONENT MALF' and numerics are shown as '-?-', it indicates a gas analyzer component is malfunctioning. Try switching the gas analyzer off and then on again.
What to do if Philips M1019A IntelliVue G5 Measuring Instruments show the same value for et and in numerics?
If your Philips Measuring Instruments display the same value for both 'et' and 'in' numerics with a 'GM NO BREATH' message, check the patient connections to ensure they are correctly set up.
Why Philips M1019A IntelliVue G5 Measuring Instruments show GM WARMUP error?
If your Philips Measuring Instruments display 'GM WARMUP' and numerics are shown as '-?-', it means the gas analyzer has not yet reached its operating temperature. Therefore, the measurement accuracy may be reduced.
What does AGT MEAS MALFUNCTION mean on Philips M1019A IntelliVue G5?
If your Philips Measuring Instruments display 'AGT MEAS MALFUNCTION,' with numerics replaced by '-?-' and an INOP tone, switch the gas analyzer off and then on again.
What does GM CHECK WATERTRAP mean on Philips M1019A IntelliVue G5 Measuring Instruments?
If your Philips Measuring Instruments display 'GM CHECK WATERTRAP', check that the sample line and/or watertrap is not disconnected.
Details final setup and configuration steps.
Lists compliance with international safety standards.
Step 1: Select MISC tab and click START in DOWNLOAD section.
Lists the types of safety tests performed.
Explains how to perform safety tests and record results.
Introduces electrical safety testing procedures.
Outlines required preventive maintenance tasks.
Explains how to check gas analyzer performance and calibration.
Procedure for periodic zero calibration of the gas analyzer.
Explains INOP messages and what to do for each.
Lists tests to perform if measurement accuracy is in doubt.
General| Device Type | Patient Monitor |
|---|---|
| Model | M1019A |
| Series | IntelliVue G5 |
| Display Type | TFT LCD |
| Parameters Monitored | ECG, SpO2, NIBP, Invasive Blood Pressure, Cardiac Output, EtCO2 |
| ECG | Yes |
| NIBP | Non-invasive blood pressure monitoring |
| Cardiac Output | Yes |
| EtCO2 | Yes |
| Connectivity | Ethernet, USB, Serial |
To Next Page