Pioneer DJM-800 Service Manual (English)

Other manuals for Pioneer DJM-800

Service Manual176 pages

Instruction Manual24 pages

Questions and Answers:

B
Bradley BowmanSep 6, 2025
Why is there no sound or low volume on my Pioneer Music Mixer?
- B
  Bryan SmithSep 6, 2025
  If you're experiencing no sound or low sound volume on your Pioneer Music Mixer, check the following: * Ensure the input selector is correctly set to the playback component. * Verify that the DIGITAL/CD or DIGITAL/LINE input selector switch on the rear panel matches the component you're using. * Confirm all connection cables are properly connected and not loose. Connect them correctly if needed. * Clean any soiled jacks or plugs before connecting. * Check the rear panel master output attenuator switch (MASTER ATT) and adjust it if it’s set to –12 dB or another reduced level.
M
Mallory AllenAug 23, 2025
How to fix distorted sound on Pioneer DJM-800 Music Mixer?
- J
  Jessica BarberAug 23, 2025
  If the sound from your Pioneer Music Mixer is distorted, it could be due to a few reasons. First, try adjusting the master output level (MASTER LEVEL) dial or the rear panel master output attenuator (MASTER ATT) switch. If that doesn't solve the issue, the input level might be too high; in this case, adjust the TRIM dial until the input level approaches 0 dB on the channel level indicator.
D
Darrell WilliamsAug 25, 2025
Why Pioneer Music Mixer BPM can't be measured correctly?
- K
  Karen BrownAug 26, 2025
  If your Pioneer Music Mixer is having trouble measuring BPM or the measured value is incorrect, it could be due to the following reasons: * The input level might be too high or too low. Adjust the TRIM dial so that the input level approaches 0 dB on the channel level indicator. * BPM may not be correctly measurable with some tracks. Adjust other channels as well so that the input levels approach 0 dB in the channel level indicator. * You can also manually set the BPM by striking the TAP button.
X
xpalmerAug 27, 2025
How to enable fader start on Pioneer DJM-800 with CD player?
- S
  Steven GreenAug 27, 2025
  If you're unable to perform a fader start with your CD player on the Pioneer Music Mixer, check the following: 1. Ensure the FADER START button is set to ON. 2. Verify that the rear panel CONTROL jack is connected to the CD player using a control cable. 3. Make sure that both the CONTROL jacks and analog input connectors are connected.
L
Lindsey FreemanAug 27, 2025
Why is external effector not working with Pioneer DJM-800?
- N
  Nicholas BrownAug 27, 2025
  If your external effector isn't working with the Pioneer Music Mixer, check these potential issues: * Ensure the effect selector is set to [SND/RTN]. * Verify that the effector is correctly connected to the rear panel SEND/RETURN connectors. * Use the effect channel selector to select the audio source to which you wish to apply the effects.
M
Michelle HartAug 28, 2025
How to troubleshoot effects not working on Pioneer Music Mixer?
- A
  Ashley CooperAug 28, 2025
  If the effects aren't working on your Pioneer Music Mixer, check that the effect channel selector is correctly set for the desired channel. Also, make sure that the effect parameter 2 adjust dial (LEVEL/ DEPTH) is not set to [MIN]; adjust it as needed.
M
mlarsenSep 12, 2025
How to fix incorrect BPM measurement on Pioneer Music Mixer?
- J
  Jennifer RoseSep 13, 2025
  If the BPM can’t be measured or the measured BPM value is incorrect on your Pioneer Music Mixer: * Adjust the TRIM dial so that the input level approaches 0 dB in the channel level indicator, because the input level may be too high or too low. * Adjust other channels as well so that the input levels approach 0 dB in the channel level indicator, because BPM may not be correctly measurable with some tracks. * Strike the TAP button to set BPM manually.
M
Mary WilsonSep 14, 2025
How to fix a cross fader that doesn't work on Pioneer Music Mixer?
- R
  Robert CopelandSep 14, 2025
  If the cross fader on your Pioneer Music Mixer isn’t working, the CROSS FADER ASSIGN switch setting ([A], [THRU], [B]) may be incorrect. Correctly set the CROSS FADER ASSIGN switch for the desired channel.
J
Jason GoodmanSep 5, 2025
Why measured BPM value is different from the value published with the CD on Pioneer DJM-800 Music Mixer?
- M
  Melissa MullinsSep 5, 2025
  Some differences may occur in the BPM value measured by your Pioneer Music Mixer compared to the value published with the CD due to differences in BPM detection methods. No remedy is necessary.
C
Curtis CarterSep 2, 2025
Why is microphone sound not produced in BOOTH output on Pioneer DJM-800 Music Mixer?
- T
  Toni WalkerSep 2, 2025
  If microphone sound isn’t being produced in the BOOTH output on your Pioneer Music Mixer, check the rear panel’s MIC SIGNAL switch. If it’s set to [CUT], switch it to [ADD].

Pioneer DJM-800 Specifications

General

Equalizer	Yes
Product color	Black
Audio output channels	4.0 channels
Signal-to-Noise Ratio (SNR)	105 dB
Total Harmonic Distortion (THD)	0.005 %
Connectivity technology	Wired
Digital audio coaxial out	1
Dimensions (WxDxH)	320 x 108 x 381 mm
Power consumption (typical)	30 W