Planet FPS-1UA - User Manual

Questions and Answers

M
Mrs. Kayla SmithNov 26, 2025
What to do if the Planet FPS-1UA Print Server unit can not be found on the LAN?
- J
  Joe GonzalezNov 26, 2025
  If your Planet Print Server unit cannot be found on the LAN, configuration is not possible. If using 10/100Base-TX: * Check the Hub. The link LED for the port to which the Print Server is connected should be ON. If it is Off, there is a problem in the network cable. * On the Print Server, check the LED(s) next to the connector. If the LED is not ON (or neither LED is On, if there are 2), the network connection is not working. Check the Ethernet cable and connectors. If they seem OK, set the DIP Switches of the Print Server to match your LAN environment. If using TCP/IP: * Ensure that there are no routers between the Print Server and the PC used for configuration. * Ensure that the PC used for configuration has the TCP/IP network protocol installed. Test its network connection by...
M
Mr. Nicholas AllenAug 23, 2025
What to do if my Planet FPS-1UA cannot print jobs sent to the print queue?
- M
  Marc CampbellAug 23, 2025
  If your Planet Print Server cannot print jobs sent to the print queue, verify the following: 1. Ensure the printer connected to the Print Server is online. 2. Confirm your Print Server is logged into the file server. 3. Check the status of the queues used by the Print Server and ensure they are active. 4. Verify the NetWare printer number is correct (0 = parallel port 1, 1 = parallel port 2, 2 = serial port or parallel port 3). 5. Check if the Print Server is a static queue server to the queue. Locate the Print Server Object and check the Queues Serviced by Printer to ensure the correct queues are on the list. 6. Ensure the total number of queues to be serviced does not exceed the limit of 56. If it does, reduce the number of queues.
K
Kristopher SandersAug 25, 2025
What to do if my Planet FPS-1UA, configured as a Novell Print Server, cannot log in to a File Server?
- M
  Monica JoyceAug 26, 2025
  If your Planet Print Server, configured as a Novell Print Server, cannot log in to a File Server, try these steps: 1. Check the Novell file server's name and ensure it is not longer than 20 characters. If it is, rename it. 2. Verify that the Print Server's configuration data, especially the password, is correct. 3. Check the NetWare server. If using Bindery mode, check the master file server to see if the login status of the Print Server is Ready. If it is not, check the error message and perform the required corrective action. 4. If the Print Server is servicing more than one file server, check that all required file servers are in the list of "File Servers To Be Serviced". If not, insert the required file server name to the list.
J
John CainAug 27, 2025
Why do I get a PostScript Command error or no print out when sending a print job to my Planet FPS-1UA Print Server?
- C
  Courtney CarterAug 27, 2025
  To resolve a PostScript Command error or no print out when sending a print job to your Planet Print Server, check the communication protocols. The computer, Print Server, and printer must all be configured to use the same communication protocol (either Binary or ASCII). To configure your system: 1. Choose which protocol you are going to use. You should check your printer; it may not give you a choice. 2. Set your printer to the correct protocol. 3. Use the computer's Print submenu to configure your computer to use the protocol you have chosen. 4. Configure the Print Server to use the same protocol as the printer and computer.
C
Crystal HuntAug 29, 2025
Why do I get an incorrect printout from my Planet FPS-1UA Print Server?
- P
  Paul GriffithAug 29, 2025
  If you are getting an incorrect printout with your Planet Print Server, it may be due to: * Using Binary encoding to print the file. Try using ASCII encoding instead. * Some fonts in your print file may not be supported by the printer. Try selecting LaserWriter 7 instead of LaserWriter 8.
J
Jessica WilsonSep 23, 2025
What to do if I can't find the Planet FPS-1UA Print Server's name in the Chooser?
- V
  velazquezkristinSep 23, 2025
  Try the following to find the Planet Print Server's name in the Chooser: 1. Make sure that AppleTalk is on (the button next to Active is highlighted in the Chooser). 2. Make sure the printer has been on and in the READY state for a few minutes. 3. Make sure the printer has not been renamed since its last appearance in the Chooser. 4. If the printer resides on a network with multiple zones, make sure the correct zone is selected from the AppleTalk Zones box in the Chooser.
M
Melissa BautistaSep 17, 2025
What to do if Planet FPS-1UA Print Server's status light and power light stay on continuously?
- J
  josephmillerSep 17, 2025
  To resolve the issue of the Planet Print Server's status light and power light staying on continuously and not turning off, reset the Print Server by unplugging the power supply or by pushing the reset push button, if fitted.
A
Alyssa SmithSep 18, 2025
How to fix Planet FPS-1UA Print Server when all the LEDs are off?
- L
  Lisa JacobsonSep 18, 2025
  Check the power supply or power connection of the Planet Print Server.
J
Jacqueline HollandSep 7, 2025
Why do I have trouble printing with the LaserWriter 8 using Planet FPS-1UA?
- V
  Victor SimpsonSep 7, 2025
  If you are having trouble printing with the LaserWriter 8 driver when using Planet Print Server, your application software may not be compatible or your system may not meet the driver's requirements. Use the Apple LaserWriter 7 driver instead.
T
Terri GarciaSep 5, 2025
What to do if my EPS file doesn't print with the correct fonts using Planet Print Server?
- H
  hardybonnieSep 5, 2025
  If your EPS file doesn't print with the correct fonts when using Planet Print Server, this issue can occur in some application programs. Try downloading the fonts contained in the EPS file before printing the saved EPS file.

Planet FPS-1UA Specifications

General

Brand	Planet
Model	FPS-1UA
Category	Print Server
Language	English

Summary

Chapter 1 Introduction and Features

Print Server Features Overview

Provides an overview of the Print Server's capabilities and benefits.

Safety Instructions

Essential safety advice for operating the Print Server and preventing damage.

Package Contents

Lists the items included with the Print Server package.

Print Server Models

Introduces the different Print Server models covered in the manual.

LED Indicators Overview

LED Status for FPS-5 P-S;5 P-M

Details the LED indicators for the FPS-5P-S and FPS-5P-M models.

LED Status for FPS-2 PUW

Details the LED indicators for the FPS-2PUW model.

LED Status for FPS-1 UA

Details the LED indicators for the FPS-1UA model.

LED Status for FPS-2 PUWG

Details the LED indicators for the FPS-2PUWG model.

DIP Switch Table and Diagnostic Button

DIP Switch Settings for FPS Models

Explains DIP switch configurations for FPS-5P-M and FPS-5P-S models.

Diagnostic Button Functions

Details the reset and diagnostic print functions of the push button.

Restoring Factory Defaults

Instructions for resetting the Print Server to its factory default settings.

Generating Diagnostic Printout

Steps to print a test page with current configuration details.

Chapter 2 LAN Installation

Installation Procedure

Step-by-step guide for installing the Print Server on a Local Area Network.

Power Up and LED Checks

Power Up Procedure

Instructions for powering on the Print Server after installation.

LED Indicator Status

Details of LED indicators for different Print Server models to verify operational status.

Chapter 3 Print Server Configuration

Overview and Configuration Methods

Provides an overview of configuration processes and alternative methods.

Chapter 4 Client PC Configuration

Overview and Wireless Settings

Outlines client configuration prerequisites and wireless setup details.

Printing Methods and Protocol Checks

Printing Method Selection

Guidance on choosing the best printing method based on system needs.

Network Protocol Verification

How to check required network protocols like TCP/IP on Windows PCs.

Windows Peer-to-Peer Print Driver

Installation Guide

Step-by-step instructions for installing the Peer-to-Peer Print Driver software.

Configure Printer Port Settings

Adding a Print Server Port

How to add a new port for the Print Server in Windows printer settings.

Manage Printing and Ports

Print Job Management

General information on managing print jobs and printers.

Port Configuration Options

Details on accessing and configuring Print Server port settings.

Windows SMB Printing Setup

Install SMB Network Printer

Steps to install a printer using the Windows SMB protocol.

Windows Server-based Print Queues

Add Network Printer

Steps to add a network printer via the Add Printer Wizard.

Windows NDPS Configuration

NDPS Setup Procedure

Steps to configure NDPS Manager and Printer Agents for printing.

Macintosh AppleTalk Configuration

AppleTalk Setup and Printing

Setting up AppleTalk and printing from Macintosh computers.

Advanced Setup for Mixed Environments

Advanced configuration for mixed Windows/Mac environments using Bi-Admin.

Chapter 5 Bi-Admin Management Utility

Requirements and Installation

System requirements and installation instructions for the Bi-Admin utility.

Bi-Admin Operation and Interface

Main Screen and Groups

Overview of the Bi-Admin interface, main screen, and group management.

Bi-Admin Configuration and Device Management

Device List and Troubleshooting

Managing the device list and troubleshooting missing Print Servers.

Bi-Admin Icons and Status

Status Icons Overview

Explains the function of status icons like Device, Port, Configuration, and Wizard.

Bi-Admin Menu Options

System and Protocol Settings

Configuring system options, network protocols, and diagnostics.

Diagnostics and Control Menus

Accessing diagnostic tools and controlling print jobs via menus.

Bi-Admin Other Functions

Upgrade and Refresh

Procedures for upgrading firmware and refreshing the device list.

SNMP Configuration Settings

Management and Trap Settings

Configuring management stations, trap receivers, and community strings.

TCP;IP Network Configuration

IP and Connection Settings

Configuring IP address, subnet mask, gateway, and connection parameters.

Configure Server Details

Name, Password, and Protocols

Setting Print Server name, password, and enabling network protocols.

Wireless Configuration Settings

Network and WEP Setup

Configuring wireless network parameters like SSID, Channel, and WEP encryption.

Other Print Server Screens

Server, Port, and Logical Printer Status

Displays status for server, ports, and configuration for logical printers.

Chapter 7 Special Features

Internet Printing Protocol (IPP)

Overview of IPP for remote printing and its server configuration.

IPP Client Setup - Windows

Installation and Configuration

Steps for installing and configuring the IPP Client software on Windows.

IPP Client Setup - Windows 2000;XP;Server 2003

Locating and Connecting to IPP Printer

Steps to locate and connect to an IPP Server printer on the network.

Using IPP Printers

Port Settings Adjustment

Adjusting retry intervals and counts for IPP connection issues.

Internet Mail Printing System

System Requirements and Configuration

Prerequisites for mail servers and clients, and general configuration.

User Software for Remote Printing

Software Installation and Port Usage

Installing InterNet Printing Port software and using the new printer port.

Printer Driver Verification and Internet Printing

Driver Check Procedure

Procedure to verify the correct remote printer driver installation.

Printing via Internet

Steps to print documents over the internet using the email system.

Canceling Print Jobs

How to cancel print jobs at the Print Server using Bi-Admin.

SNMP Configuration and Usage

SNMP Setup and Management

Configuring SNMP settings for management stations and trap receivers.

Wireless Configuration for Models

Model-Specific Wireless Setup

Details wireless modes and required configurations for FPS-2PUW/2PUWG.

Wireless Link Information

Link Info Details Explanation

Explanation of data fields showing wireless connection quality and status.

Chapter 8 Troubleshooting

Overview and Hardware;LAN Issues

Introduction to troubleshooting and solutions for hardware and LAN problems.

Macintosh AppleTalk Troubleshooting

Common AppleTalk Printing Issues

Solutions for incorrect printouts, chooser name, printer assignment, and font problems.

Novell NetWare Troubleshooting

Print Queue and Login Issues

Solutions for problems with print queues and NetWare file server login.

Windows Printing Problem Solutions

Installation and Printer Setup Issues

Resolving errors during Peer-to-Peer installation and printer setup failures.

Appendix A Specifications

General Hardware Specifications

Lists general hardware specifications for various Print Server models.

Parallel Port Pin Assignments

Protocol and Feature Support Summary

Protocol Support Table

Summarizes protocol compatibility across different Print Server models.

Feature Support Table

Outlines supported features like HTTP, IPP, and SNMP for each model.

Regulatory Approvals Information

Appendix B Network Server Configuration

Windows NT Server TCP;IP Printing

Steps to prepare and install TCP/IP printing support on Windows NT.

Adding a TCP;IP Remote Printer

Windows 3.51 and NT 4.0 Procedures

Detailed steps for adding TCP/IP remote printers on Windows 3.51 and NT 4.0.

Network Server Configuration Examples

Windows 2000;XP;Server 2003 Printer Setup

Instructions for adding network printers on Windows 2000, XP, and Server 2003.

Novell NetWare Configuration Methods

Configuration methods for Novell NetWare systems with Print Servers.

Advanced Configuration Methods

Bi-Admin for NetWare

Using Bi-Admin to configure NetWare Servers and Print Servers.

Alternative Configuration Tools

Using WPConfig, PSConfig, and Quickset for configuration.

Required Configuration Data

Details general and mode-specific data needed for Print Server setup.

Setup for NDPS (NetWare 5)

NDPS Manager Object Creation

Procedure to create an NDPS Manager object in NetWare Administrator.

Creating an NDPS Printer Agent

Unix Systems Configuration and Printing

Unix Printing Methods Support

Details supported Unix printing methods like LPD, FTP, and PSfilter.

Related product manuals

Planet FPS-5P-M

93 pages