To Next PageTo Next PageWhat to do if my Polaris 9400 Sport does not move on startup?
First, ensure the outlet the control unit is connected to is receiving electrical power. If the outlet is working, check that you have started one of the two programs and that the indicator for the selected program is lit. If it still doesn't move, contact your local Polaris service representative.
Why is my Polaris Swimming Pool Vacuum not staying firmly on the pool bottom?
If your cleaner isn't staying on the pool bottom, it might have air in the appliance casing. Submerge the cleaner following the procedure in Section 4.1, 'Submerging the Cleaner'.
Why is my Polaris 9400 Sport not climbing the pool sides?
Your Polaris Swimming Pool Vacuum might not climb the pool sides because the filter is full or dirty. Clean the filter canister. Also, the pool sides might be slippery due to microscopic algae. Perform a shock chlorination treatment and slightly reduce the pH, but do not leave the cleaner in the pool during this treatment.
How to fix a Polaris 9400 Sport remote control that does not work?
If your remote control isn't working, first replace the batteries. If that doesn't solve the problem, the remote control may not be synchronized to the control unit. To synchronize, connect the 9300xi sport to the control unit, then plug the control unit into the receptacle. Press OFF + Cycle I buttons for more than 6 seconds until both lights flash once. Then, press and hold the 'rotate right' button on the remote control. The light on the right will flash 5 times, then both lights will flash together. The synchronization is complete when both lights switch off.
What to do if the cycle I and II program indicators flash alternately on my Polaris Swimming Pool Vacuum?
This indicates your cleaner has encountered a problem during its operation. Try these steps: disconnect the control unit and wait 20 seconds before reconnecting it. Check that the cable is correctly connected, and that no debris impedes the rotation of the brushes or the propeller. Also, clean the filter. Start a new cleaning program. If the problem continues contact your local Polaris service representative.
What to do if flashing indicator lights appear just after starting my Polaris 9400 Sport?
If the indicator lights flash right after starting, ensure the floating cable is properly plugged into the control unit. Unplug and replug it. Also, make sure the cleaner is fully submerged. If it still flashes, reset the cleaner by pressing the power button OFF and then Cycle I or II to start a new cycle. If the propeller or wheels do not turn, contact your local Polaris service representative.
What to do if the flashing lights appear during the cycle of my Polaris 9400 Sport Swimming Pool Vacuum?
If the lights flash during the cycle, it could be because the cleaner is sucking air for 60 seconds. Submerge the cleaner following the procedure in Section 4.1, 'Submerging the Cleaner'.
General| Brand | Polaris |
|---|---|
| Model | 9400 Sport |
| Category | Swimming Pool Vacuum |
| Language | English |
Details the general specifications for the cleaner, including voltage, load, and dimensions.
Step-by-step guide to assembling the transport caddy and its components.
Instructions for connecting the control unit to the caddy for proper setup.
Procedure for safely connecting the cleaner's control unit to a power source.
Steps for properly submerging the cleaner into the pool and preparing it for operation.
Overview of the control unit for the 9300/P93 models.
Overview of the control unit for the 9400 Sport/P94 models.
Overview of the control unit for the 9500 Sport/P95 models.
Instructions on how to start the cleaner, including setting preferences.
Guide to stopping the cleaner and safely removing it from the pool.
How to operate the cleaner using the remote control for 9500 Sport/P95 models.
Procedure for synchronizing the remote control with the cleaner's control unit.
Proper methods for cleaning and storing the cleaner after use.
How to view the current day and time settings on the control unit.
Instructions for setting or changing the day and time on the control unit.
Procedure to modify the default cleaning time durations for pool surfaces.
Guide to setting up multiple cleaning cycles for specific days and times.
Steps to cancel programmed cleaning cycles, either individually or all.
Detailed guide on how to clean the filter canister after each cleaning cycle.
Information and tips for preventing and resolving issues with cord tangling.
Procedure for checking brush wear and replacing worn brushes to maintain performance.
Instructions on how to remove and replace the tires on the cleaner's wheels.
