What to do if my Polygroup Swimming Pool Pump has leakage at hoses?
Ensure that the hose clamps are tightened or reinstalled. Also, check that the O-rings of the hose connections are in place and intact.
Why is my Polygroup Water Pump not pumping water or the flow is very slow?
If your Polygroup Water Pump isn't pumping water or the flow is very slow: * Clear any obstructions in the pool outlet fitting and pump intake hose. * Tighten hose clamps, check hoses for damage and check pool water level to resolve a potential air leak on the intake line. * Backwash the sand bed more frequently if the sand media is clogged with dirt. * Replace about 1" (25mm) of sand if there's crusting or caking on the filtering sand surface. Replace all the sand if the problem persists. * Remove any pool vacuuming device attached to the system line.
Why isn't my Polygroup Water Pump sand filter cleaning the pool?
If the Polygroup Water Pump sand filter isn't cleaning the pool: * Adjust the chlorine and pH levels. * Load the tank with filter sand. * Set the 6-port valve to the “FILTER” position. * Operate the filter for longer periods if the pool is excessively dirty. * Clean the strainer at the pool outlet fitting if an obstructed pool outlet fitting is restricting the water flow.
What to do if my Polygroup Water Pump hose is leaking?
If your Polygroup Water Pump hose is leaking: * Tighten or reinstall the hose clamp(s) securely. * Ensure the o-ring is in place and not damaged at the hose connection fitting.
Why is sand ending up in my Polygroup Swimming Pool?
This may be happening because the sand is too small for the pump. Use only #20 grade silica sand with a particle size range of 0.45-0.85 mm (0.018-0.033 inches) and a uniformity coefficient less than 1.75. Another cause may be that the sand bed is calcified, in that case you should discard all the used sand and replace it with new sand.
What to do if the pressure gauge on my Polygroup Swimming Pool Pump doesn't work?
Unscrew and remove the gauge, then clear any obstructions in its inlet.
Why does sand end up in the pool with my Polygroup Water Filtration Systems?
If sand ended up in your pool when using the Polygroup water filtration system, use only #20 grade silica sand with a particle size range of 0.45-0.85 mm (0.018-0.033 inches) and a uniformity coefficient less than 1.75. If the sand bed is calcified, discard all the used sand and replace it with new sand.
How to fix a leaking 6-port valve on my Polygroup Water Filtration Systems?
If the 6-port valve or its locking ring is leaking on your Polygroup water filtration system, first remove the 6-port valve and check to ensure the gasket is in place. If the gasket is dirty, clean it with garden hose water. Also, tighten or reinstall any loose hose clamps.
What to do if Polygroup Lighting Equipment sand filter doesn’t clean the pool?
If the Polygroup Lighting Equipment sand filter isn’t cleaning the pool, adjust the chlorine and pH levels, consulting local pool supply stores for guidance. Ensure the sand tank is filled according to the setup instructions. Verify the 6-port valve is set to the “FILTER” position. If the pool is excessively dirty, run the pump for a longer duration. Also, clean the strainer of the suction fitting.
Why is the Polygroup Lighting Equipment sand filter not pumping water or has very slow flow?
If the Polygroup Lighting Equipment sand filter doesn't pump water well, start by cleaning the suction fitting and the hose connecting it to the pump inlet. Check the intake hose for damage and ensure the hose clamps are tight, also check the pool water level. If the sand is too dirty, backwash it more frequently. For crusting or caking of the sand surface, replace about 1 inch of the sand, or all of it if the problem continues. Also, remove any pool vacuuming devices attached to the pump.
Guidance on protecting children from drowning risks and pool access.
Information on required barriers for pool safety and preventing access by children.
Guidelines for safe installation and placement of electrical pool equipment.
Safety precautions related to electric shock and pump operation.
Details on wattage and amperage for different sand pump models.
Comprehensive list of all components included with the sand filter pump.
List of tools necessary for assembling the sand filter pump.
Step-by-step instructions for attaching suction fittings to the pool.
Instructions for connecting the return fitting to the pool inlet.
Procedure for securing the pump onto the sand tank base.
Explains the different functions and water flow directions of the 6-port valve.
Detailed explanation of the GFCI plug's features, buttons, and display.
Routine maintenance tasks for the pump, including backwashing and cleaning.
Guidelines for maintaining water quality, pH, and chlorine levels.
Rules for installing SOFA to prevent suction entrapment and ensure compliance.
General| Model | ST1100 |
|---|---|
| Voltage | 120V |
| Power Source | Electric |
| Hose Size | 1.25 inches |
| Type | Swimming Pool Pump |
| Pump Type | Above Ground Pool Pump |
| Flow Rate | 1100 GPH |
| Power Cord Length | 25 ft |
To Next Page