How to fix Polygroup Swimming Pool Pump hose leaking?
If your Polygroup Swimming Pool Pump hose is leaking: * Ensure hose clamps are securely tightened or reinstall them. * Check that the hose connection fitting o-ring is in place and not damaged.
Why is my Polygroup Water Pump not pumping water or the flow is very slow?
If your Polygroup Water Pump isn't pumping water or the flow is very slow: * Clear any obstructions in the pool outlet fitting and pump intake hose. * Tighten hose clamps, check hoses for damage and check pool water level to resolve a potential air leak on the intake line. * Backwash the sand bed more frequently if the sand media is clogged with dirt. * Replace about 1" (25mm) of sand if there's crusting or caking on the filtering sand surface. Replace all the sand if the problem persists. * Remove any pool vacuuming device attached to the system line.
Why isn't my Polygroup Water Pump sand filter cleaning the pool?
If the Polygroup Water Pump sand filter isn't cleaning the pool: * Adjust the chlorine and pH levels. * Load the tank with filter sand. * Set the 6-port valve to the “FILTER” position. * Operate the filter for longer periods if the pool is excessively dirty. * Clean the strainer at the pool outlet fitting if an obstructed pool outlet fitting is restricting the water flow.
What to do if the pressure gauge on my Polygroup SUMMER WAVES ST1600 Swimming Pool Pump doesn't work?
Unscrew and remove the gauge, then clear any obstructions in its inlet.
What causes Polygroup SUMMER WAVES ST1600 6-way valve/ cover leaking?
A leaking 6-way valve or cover on your Polygroup Swimming Pool Pump can be caused by: * A missing sand tank o-ring: Remove the 6-way valve and ensure the o-ring is present. * A dirty sand tank o-ring: Clean the sand tank o-ring with garden hose water. * Loose hose clamps: Tighten the hose clamps.
What to do if my Polygroup SUMMER WAVES ST1600 has leakage at hoses?
Ensure that the hose clamps are tightened or reinstalled. Also, check that the O-rings of the hose connections are in place and intact.
Why does sand end up in the pool with my Polygroup Water Filtration Systems?
If sand ended up in your pool when using the Polygroup water filtration system, use only #20 grade silica sand with a particle size range of 0.45-0.85 mm (0.018-0.033 inches) and a uniformity coefficient less than 1.75. If the sand bed is calcified, discard all the used sand and replace it with new sand.
How to fix a leaking 6-port valve on my Polygroup Water Filtration Systems?
If the 6-port valve or its locking ring is leaking on your Polygroup water filtration system, first remove the 6-port valve and check to ensure the gasket is in place. If the gasket is dirty, clean it with garden hose water. Also, tighten or reinstall any loose hose clamps.
Why is sand ending up in my Polygroup Swimming Pool?
This may be happening because the sand is too small for the pump. Use only #20 grade silica sand with a particle size range of 0.45-0.85 mm (0.018-0.033 inches) and a uniformity coefficient less than 1.75. Another cause may be that the sand bed is calcified, in that case you should discard all the used sand and replace it with new sand.
Why is the Polygroup Lighting Equipment sand filter not pumping water or has very slow flow?
If the Polygroup Lighting Equipment sand filter doesn't pump water well, start by cleaning the suction fitting and the hose connecting it to the pump inlet. Check the intake hose for damage and ensure the hose clamps are tight, also check the pool water level. If the sand is too dirty, backwash it more frequently. For crusting or caking of the sand surface, replace about 1 inch of the sand, or all of it if the problem continues. Also, remove any pool vacuuming devices attached to the pump.
Provides guidance on child safety around swimming pools, emphasizing supervision and risk reduction.
Warns about entrapment hazards from suction outlets and advises on immediate actions if covers are missing.
Advises on preventing child access to pools via fencing and proper placement of pool equipment and toys.
Emphasizes keeping electrical appliances away from pools and avoiding installation near overhead electrical lines.
Provides critical safety warnings and general information regarding SOFA installation and use.
Details the specific requirements and limitations for installing SOFA components to prevent suction entrapment.
This document serves as an owner's manual for the Summer Waves Sand Filter Pump, designed for above-ground swimming pools, specifically models ST1100 (10") and ST1600 (12"). It provides comprehensive instructions for setup, operation, maintenance, and troubleshooting, emphasizing safety precautions throughout.
The primary function of this device is to filter and circulate water in above-ground swimming pools, ensuring water clarity and hygiene. It utilizes #20 silica sand as a filtration medium, which can be purchased from local home improvement or building material stores. The manual explicitly warns against using incorrect sand, as it may damage the filtration system and void the warranty.
The sand filter pump is equipped with a 6-Port Valve, which offers multiple functions for pool maintenance:
The pump is designed for ease of use, with clear instructions for connecting hoses and fittings. It includes a GFCI (Ground-Fault Circuit-Interrupter) power cord set with a pre-set timer function. The default operating time is 10 hours, after which the pump automatically turns off for 14 hours, following a 24-hour cycle. Users can adjust the operating time from 1 to 10 hours using the "SET" button. The manual provides detailed instructions on how to test the GFCI's leakage protection function, emphasizing safety by ensuring the pump stops working if a ground current is detected.
For installation, the manual outlines steps for setting up the pool, installing suction and return fittings, and assembling the pump onto its base. It highlights the importance of aligning the clamp hinge with the ridge on the 6-Port Valve flange for a secure fit. The sand tank should be filled with #20 silica sand, ensuring the sand level is between the Min and Max marks on the Center Pipe.
Regular maintenance is crucial for the longevity and efficient operation of the sand filter pump.
The manual includes extensive safety warnings, such as preventing drowning by supervising children, avoiding diving into shallow water, and staying away from drains and suction fittings to prevent entrapment. It also provides electrical safety guidelines, including connecting to a grounding-type receptacle, using a GFCI, and maintaining a safe distance from electrical outlets. The document references various safety standards and organizations like ASME, ANSI, APSP, and NEC, highlighting the importance of adhering to local and state building codes for pool installation and safety barriers.
General| Model | ST1600 |
|---|---|
| Voltage | 120V |
| Flow Rate | 1600 GPH |
| Recommended Pool Size | Above Ground Pools |
| Power | 0.75 HP |
| Motor Power | 0.75 HP |
To Next Page