If your PSV is equipped with a fluid stage, you must proceed with theIf your PSV is equipped with a fluid stage, you must proceed with the
assembly as follows:assembly as follows:
1.1. AsseAssemble the trmble the tripod as desipod as describecribed in the assemd in the assembly instbly instructructions proions providevided byd by
the manufacturer MANFROTTO.the manufacturer MANFROTTO.
2.2. Then moThen mount the funt the fluid stluid stage as desage as describcribed in the ased in the assemblsembly insty instructructionsions
provided by the manufacturer MANFROTTO.provided by the manufacturer MANFROTTO.
3.3. Open thOpen the lockie locking mechng mechanisanism on the flum on the fluid staid stage by simge by simultultaneouaneouslysly
pressing the safety latch and opening the safety lever.pressing the safety latch and opening the safety lever.
4.4. A suitA suitable quable quick relick release heease hexagoxagonal platnal plate has been pe has been pre-mre-mounteounted on thed on the
scanning head. Use this plate to position the scanning head on the fluidscanning head. Use this plate to position the scanning head on the fluid
stage.stage.
5.5. EnsuEnsure that tre that the quiche quick releak release platse plate is attae is attached alched all the way arl the way around. Tound. Thishis
needs to be done before the needs to be done before the scanning head is ready to use.scanning head is ready to use.
6.6. WheneWhenever you wver you want to reant to remove tmove the scanhe scanning hening head from thad from the fluid se fluid stagetage,,
one person should hold the scanning head while the second person opensone person should hold the scanning head while the second person opens
the safety lever.the safety lever.
7.7. Keep thKeep the asseme assembly insbly instructructiontions for the trs for the tripod and tipod and the fluihe fluid stagd stage in a safee in a safe
place.place.
If your PSV is equipped with a pan-tilt stage you must proceed with theIf your PSV is equipped with a pan-tilt stage you must proceed with the
assembly as follows:assembly as follows:
1.1. UnpaUnpack the panck the pan-til-tilt stage ant stage and check it fod check it for externr external damage (sal damage (scratcratchesches,,
loose screws, etc.).loose screws, etc.).
2.2. ChecCheck tk the che contenontents ts of tof the ashe assemblsembly kiy kit:t:
1 Adapter plate wit1 Adapter plate with 3 Allen screwh 3 Allen screws M6s M6xx 1616
1 Connector box wi1 Connector box with 4 Allen screwth 4 Allen screws M8s M8 xx4040
3 Allen screws 3 Allen screws M8M8 xx 16 with washe16 with washersrs
1 Mounting plate wi1 Mounting plate with 2 Allen screwth 2 Allen screws M6s M6xx2020
2 Allen screws 2 Allen screws M6M6 xx 16 with washe16 with washersrs
1 Allen key size 51 Allen key size 5
1 Allen key size 61 Allen key size 6
3.3. AttAttach the mach the mountounting plating plate on the undee on the undersidrside of the scae of the scanning hnning head witead withh
22 Allen screwAllen screws M6s M6 xx20. T20. To do this use the Ao do this use the Allen key size 5.llen key size 5.
Make sure that the screws are always tightened, to ensure that the system is both stableMake sure that the screws are always tightened, to ensure that the system is both stable
and functionand functions accurates accuratelyly !!
Make sure that the mounting plate is correctly aligned! The FRONT labeled side of the plateMake sure that the mounting plate is correctly aligned! The FRONT labeled side of the plate
has to be mounted in the direction of the front panel of the scanning head as shown inhas to be mounted in the direction of the front panel of the scanning head as shown in
fig
figururee 3.3.1212..
To Next Page
Loading...
