Why is my Pottinger FARO 4000 L/D torque limiter on the driveshaft triggered?
The torque limiter on the driveshaft of your Pottinger Farm Equipment might be triggered due to several reasons: too much forage at once, a large foreign body, or blunt knives. To resolve this, declutch and start off again at low revs. If there's a foreign body, remove it and sharpen the knives. If the knives are blunt, sharpen them.
What to do if my Pottinger FARO 4000 L/D Farm Equipment has poor cutting quality?
If your Pottinger Farm Equipment exhibits poor cutting quality, it could be due to blunt knives or the p.t.o. speed being too high. Sharpen or replace the knives. Also, drive at lower revs to avoid picking up larger wads of forage.
What to do if my Pottinger Farm Equipment forage jams?
If forage jams occur in your Pottinger Farm Equipment, it might be because the travel speed is too high, or the trailer is hitched up too low. To fix this, set the drawbar to the correct height.
What to do if my Pottinger FARO 4000 L/D Farm Equipment transmission runs hot?
If the transmission of your Pottinger Farm Equipment runs hot, it's likely due to a lack of lubrication. Top up or replace the oil to resolve this issue.
What to do if my Pottinger FARO 4000 L/D Farm Equipment has poor braking?
Poor braking in your Pottinger Farm Equipment can be caused by worn brake linings. You should adjust or replace the linings.
What to do if my Pottinger FARO 4000 L/D picks up forage soiled?
If your Pottinger Farm Equipment picks up soiled forage, the jockey wheels might be set too low. Check the jockey wheel setting to correct this.
What to do if my Pottinger FARO 4000 L/D jockey wheels do not reach ground?
If the jockey wheels on your Pottinger Farm Equipment do not reach the ground, the pick-up might be set wrong. Adjust the jockey wheels and check the height setting at the hitch.
Why is there noise from transmission chain in my Pottinger FARO 4000 L/D Farm Equipment?
Noise from the transmission chain in your Pottinger Farm Equipment usually indicates that the chain is loose. Check the chain tension regularly (5 to 8 mm play) and tighten it if necessary.
What to do if hydraulic mechanism move jerkily in my Pottinger FARO 4000 L/D Farm Equipment?
If the hydraulic mechanism in your Pottinger Farm Equipment moves jerkily, there might be air in the lines or cylinders. Loosen the bleed screws (A) and bleed the lines to resolve this.
Why does the scraper floor chain run noisily in my Pottinger Farm Equipment?
A noisy (ticking over) scraper floor chain in your Pottinger Farm Equipment is often due to the chain being either too loose or too taut. Check the chain tension.
Outlines crucial checks and preparations required before operating the machine.
Lists common machine faults, their causes, and recommended solutions for repair.
Lists common machine faults, their causes, and recommended solutions for repair.
Explains hydraulic connection procedures and how to connect hydraulic lines.
Introduces the "DIRECT CONTROL" unit, its buttons, and general operation.
Provides detailed instructions for specific loading functions like scraper floor and pick-up.
Details specific unloading functions, including scraper floor and tailgate operations.
Explains how to carry out hydraulic functions and interpret control lights (LEDs).
Guides on checking status, activating functions, and lists benefits of automatic loader/unloader.
Outlines required connections and explains the control panel layout and button functions.
Guides through the initial setup and navigating the WORK menu functions.
Details specific loading operations like scraper floor, cutting unit, and drawbar control.
Details specific unloading operations for automatic unloader, scraper floor, and forward run.
Explains operation of regulating rollers, cross conveyor belt, and trailing forward axle.
Details tailgate operation, stop function, and value adjustments.
Explains fault monitoring, symbols, and how to manage diagnostics and alarms.
Details charging procedures and how LED indicators display the AC charge level.
Maps the ISO-terminal interface, menus, and button functions.
Explains the start, base setting, and loading menus with their button indications.
Details the unloading menu functions and button indications without a cross conveyor.
Details the unloading menu functions and button indications with a cross conveyor.
Describes the set menu and detailed operation of the trailing front axle.
Covers setting instants, lead time, and the TEST menu.
Explains the diagnostic menu, fault symbols, and matrix fields for system checks.
Guides on configuring and setting the joystick for loader wagon operation.
Describes tractor data transmission and setting speed parameters.
Provides loading process basics, pick-up adjustment, and starting steps.
Details unloading steps, shut-off clutch, and finishing the process.
General| Brand | Pottinger |
|---|---|
| Model | FARO 4000 L/D |
| Category | Farm Equipment |
| Language | English |
To Next Page