EasyManua.ls Logo

Powermatic PM1800B - User Manual

Powermatic PM1800B
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating Instructions and Parts Manual
18-, 20-, 24-inch Band Saws
Models PM1800B, PM2013B, PM2415B
PM2013B shown
Powermatic
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-1791800B
Ph.: 800-274-6848 Revision B 02/2018
www.powermatic.com Copyright © 2018 Powermatic

Table of Contents

Questions and Answers

  • K
    Katie MartinAug 23, 2025
    Why does Powermatic PM1800B blade break prematurely?
    • K
      Kyle JenningsAug 23, 2025
      If the blade on your Powermatic Saw is breaking too soon, consider these possible causes and solutions: * **Excessive Feed Force:** Reduce the force with which you're feeding material into the saw. * **Incorrect Blade Pitch:** Consult the blade selection chart and switch to a blade with a finer pitch. * **Inadequate Support Bearing:** Check the support bearing for proper positioning and wear. Adjust or replace it as needed. * **Over Tensioned Blade:** Reduce the tension on the blade.
  • M
    Martin CoffeyAug 26, 2025
    How to stop Powermatic Saw table vibration?
    • J
      James CarneyAug 26, 2025
      If you're experiencing table vibration while sawing with your Powermatic Saw, several factors could be contributing: * **Incorrect Blade Speed:** Adjust the belt position to achieve the correct speed, and ensure your feed rate matches the material. * **Loose Drive Belt:** Increase the tension on the drive belt, and replace it if it's worn. * **Incorrect Blade Pitch:** Use the correct blade according to the blade selection chart. * **Contaminated Band Wheel:** Clean any sawdust or debris from the band wheel, and replace the tires if they are worn or damaged. * **Worn Support Bearings:** Replace any worn support bearings.
  • J
    Jennifer HayesAug 28, 2025
    Why is the surface finish rough on my Powermatic PM1800B Saw?
    • K
      Kathleen EspinozaAug 28, 2025
      If the surface finish on your workpiece is rough when using the Powermatic Saw, it could be due to: * **Low Blade Speed:** Increase the saw blade speed. * **Coarse Blade Pitch:** Change to a blade with a finer pitch.
  • T
    Timothy ValenciaAug 30, 2025
    What causes cracks on the back edge of Powermatic PM1800B blade?
    • O
      Olivia YoungAug 30, 2025
      Cracks appearing on the back edge of your Powermatic Saw blade can be attributed to a few reasons: * **Excessive Feed Speed:** Reduce the speed at which you're feeding the workpiece to lessen the strain on the blade. * **Improper Blade Welding:** Replace the blade, ensuring proper welding or acquiring a new blade. Round the back edge of a new blade. * **Worn Thrust Bearing:** Replace the thrust bearing and adjust the new bearing as per the instructions.
  • M
    Michael Castillo MDSep 2, 2025
    What causes premature dulling of Powermatic PM1800B teeth?
    • S
      Stacy WilliamsSep 2, 2025
      Premature dulling of saw teeth on your Powermatic Saw can occur due to several reasons: * **Fine Blade Pitch:** Use a blade with a coarser pitch. * **Light Feed Pressure:** Increase the feed pressure. * **Low Cutting Rate:** Increase both feed pressure and cutting rate. * **Incorrect Blade Choice:** Select the proper blade from the chart after re-examining the material. * **Foreign Object Lodged:** Stop the saw and remove any lodged particles. Replace the blade if it's damaged.
  • R
    Randall McclainSep 4, 2025
    Why Powermatic PM1800B table tilt does not hold position?
    • J
      John MartinSep 4, 2025
      If the table tilt on your Powermatic Saw doesn't hold its position under load, it could be due to: * **Loose Locking Lever:** Tighten the locking lever. * **Broken Trunnion Locking Mechanism:** Replace the trunnion locking mechanism.
  • T
    tolsonSep 6, 2025
    Why Powermatic PM1800B Saw blade forms cracks at base of teeth?
    • A
      Anne Clark PhDSep 6, 2025
      If your Powermatic Saw blade is forming cracks at the base of the teeth, consider the following: * **Unsuitable Teeth:** Replace the blade with one suitable for the job. * **Incorrect Blade Thickness:** Replace with a blade of proper thickness. * **Improper Sharpening:** Sharpen the blade correctly or replace it. If the band wheels have become misaligned, contact a service representative.
  • M
    Melissa SmithSep 8, 2025
    Why Powermatic Band Saw does not come up to speed?
    • S
      sheila36Sep 8, 2025
      If your Powermatic Band Saw isn't reaching its full speed, there might be a couple of reasons: * **Inadequate Extension Cord:** Replace the extension cord with one of adequate size and length. * **Low Current:** Contact a qualified electrician to check the current supply.
  • D
    Daniel LopezSep 12, 2025
    What to do if Powermatic Saw table will not tilt?
    • D
      Debbie MathewsSep 12, 2025
      If the table on your Powermatic Saw won't tilt, it might be because: * **The trunnion is not lubricated:** Lubricate the trunnion. * **The trunnion is jammed:** Disassemble and replace the jammed parts.
  • K
    Keith ArmstrongSep 13, 2025
    Why Powermatic PM1800B Saw blade breaks close to weld?
    • K
      Krystal PearsonSep 13, 2025
      If the blade on your Powermatic Saw is breaking close to the weld, it could be due to: * **Blade Overheating During Welding:** Have the blade annealed or eliminate the brittle part and weld it correctly. * **Rapid Cooling After Welding:** Have the blade annealed or eliminate the brittle part and weld it correctly.

Powermatic PM1800B Specifications

General IconGeneral
Motor Power3 HP
Voltage230V
Blade Diameter18 inches
Dust Port Size4 inches
Phase1 Phase
Table Size27 inches x 40 inches
Cutting Capacity16 inches
Arbor Size5/8 inches

Related product manuals