INDEX
1 GATE OPERATOR CLASSIFICATIONS ....................................... 4
2 SAFETY ACCESSORY SELECTION ............................................. 4
3 ENTRAPMENT PROTECTION TYPES ......................................... 4
4 IMPORTANT SAFETY INSTRUCTIONS ..................................... 5
4.1 – Safety Installation Information ............................. 5
5 TECHNICAL SPECIFICATION ....................................................... 6
6 REQUIRED TOOLS FOR INSTALLATION .................................. 7
7 ELECTRICAL INSTALLATION ....................................................... 7
8 PRECAUTIONS FOR ELECTRICAL INSTALLATION ............... 8
9 INSTALLING AND FIXING THE OPERATOR ............................ 8
10 - LIMIT SWITCH INSTALLATION .................................................12
11 - INTRODUCTION: ELECTRONIC SYSTEM’S TECHNICAL
FEATURES ...............................................................................................13
12 - CONTROL BOARD ........................................................................13
12.1 - Overview .................................................................. 13
12.2 - Power Supply ........................................................... 14
12.3 - Induction Motor Connection ............................. 14
12.4 - ‘ENC’ encoder connection ...................................14
12.5 - ‘TRAVA’ Audio Alarm connection ......................15
12.6 - ‘LUZ’ courtesy light connection .........................15
12.7 - ‘RX’ separated receiver connection .................. 15
12.7 - ‘RX’ separated receiver connection .................. 15
12.8 - ‘BOT’ pushbutton connection ............................ 15
12.9 - ‘HIB’ end-of-stroke reeds connection .............. 15
12.10 - ‘SCI’ connector ....................................................... 15
13 - ENTRAPMENT PROTECTION SYSTEMS .................................16
13.1 - Internal Entrapment Protection
System (Type A) ..................................................................16
13.2 - External Entrapment Protection
System (Type B1) ................................................................16
13.3 - ‘FOT’ closing cycle photoelectric sensor ........17
13.4 - ‘FEC’ opening cycle photoelectric sensor ......17
13.5 - Miller Edge reexi Gard Connection ...............18
13.6 - ‘ABR’ audio alarm reset connection ..................19
14 - FORCE ADJUSTMENT ................................................................. 19
14.1 - ‘FOP’ High Speed Force Adjustment ................19
14.2 - ‘FME’ Low Speed Force Adjustment ................. 20
15 - GATE SYSTEM LOGIC FUNCTION ...........................................20
15.1 - First operation after a frequency
inverter is installed on the operator (Gate travel
recognition) .......................................................................... 20
15.2 - From the second activation on, when the
control board is disconnected from the power
supply ..................................................................................... 20
16 - INVERTER PARAMETERS PROGRAMMING ..........................21
16.1 - Operator model selection ................................... 21
16.2 - JUMPER TST .............................................................. 21
16.3 - Adjustment of other parameters ...................... 21
17 - ERASING THE RECOGNIZED GATE TRAVEL .........................24
18 - APPLYING THE DEFAULT STANDARD SETTINGS ...............24
19 – ADDING A REMOTE CONTROL ...............................................24
19.1 – Remote control functions ..................................24
19.2 - The remote control battery.................................25
20 - SELECTION OF RF RECEPTION PROTOCOL (CR/CF
JUMPER) .................................................................................................. 26
21 - ERASING ALL STORED REMOTE CONTROLS ......................26
22 - USER OPERATION ........................................................................ 26
22.1 - Unlocking (manual release and
operation) .............................................................................27
23 - ACCESSORIES ................................................................................27
23.1 - Garage Light .............................................................27
23.2 - Flashing lights .........................................................28
24 - EVENT / FAILURE INDICATION .................................................28
24.1 - Microcontroller functioning indication ..........28
24.2 – Indication of over current or short
circuit on the motor .........................................................28
24.3 – Overheating indication ....................................... 28
24.4 – EEPROM fault indication ..................................... 28
24.5 – EEPROM invalid data indication ....................... 28
24.6 - Open end-of-stroke indication ..........................29
24.7 - Close end-of-stroke indication .......................... 29
24.8 - Capacitor load indication ....................................29
24.9 - Encoder Test ............................................................. 29
24.10 - Thermal Protection ..............................................29
25 - MAINTENANCE .............................................................................29
26 - REPAIR PARTS ................................................................................30
To Next Page
Loading...
