w ww.practixx .com
GB
|
37
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
13.1 Replacing the blade (7) (Fig. 26)
m ATTENTION!
Switch on the mower with the -button before start-
ing with the work.
m NOTE:
The blades (7) must be replaced after approx. 8
weeks. (2 sets of 3 blades each are included in the
delivery)
Use only original blades from the manufacturer. (Art.
no. 7913001601)
m ATTENTION!
Put on protective gloves before replacing the blade
(7).
m ATTENTION!
All blades (7) must always be changed at the same
time. The changing of individual blades (7) is not per-
mitted.
If the Phillips screws (8) are damaged or can no
longer be tightened, these must also be replaced.
New screws are included with the replacement
blades.
• To replace the blades (7), place the robotic lawn-
mower (1) on a workbench with the underside fac-
ing upwards. (We recommend a soft base to avoid
damage to the housing).
• Loosen the Phillips screw (8) with the help of a
Phillips screwdriver (not included in the scope of
delivery).
• Remove the old blade (7).
• Fit the new blade (7) and fasten it with a new screw
(8).
• Check that the blade (7) can move.
If this is not the case, loosen the screw (8) a little.
• Carry out this operation on all three blades (7).
13.2 Inserting/removing the battery (Fig. 27/28)
m ATTENTION!
Switch the mower o before starting with the work.
• To install/remove the battery, place the robotic
lawnmower (1) on a workbench with the underside
facing upwards. (We recommend a soft base to
avoid damage to the housing).
Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product. Make sure that no water can
penetrate the product interior.
11. Transport
• Press the -button (“POWER ON/OFF” button) un-
til the robotic lawnmower (1) switches on. -button
(“POWER ON/OFF” button) to switch the robotic
lawnmower (1) o.
• Wear protective gloves when transporting the ro-
botic lawnmower (1).
• Carry the robotic lawnmower (1) securely with both
hands.
To prevent damage, avoid the robotic lawnmower (1)
falling to the ground from greater heights.
If this does happen, it must be immediately taken to a
specialist workshop for inspection.
Do not continue to use the robotic lawnmower (1) be-
fore this has been done.
12. Storage/Hibernation
Your mower will give you pleasure for longer if it is
allowed to hibernate.
Although this is not a problem, we recommend that
you store your mower in a closed room, e.g. in the
garage, during the winter.
Before storing the mower:
• Clean it thoroughly (see point 10)
• Charge the battery fully.
• Switch the product o.
• Remove the battery (see point 13.2).
Store the product and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
40 ˚C.
Store the robotic lawnmower (1) in its original pack-
aging.
Cover the robotic lawnmower (1) to protect it from
dust and moisture.
Store the operating manual with the robotic lawn-
mower (1).
13. Maintenance / Update
m ATTENTION!
Before carrying out maintenance work, switch the
product o with the -button.
To Next Page
Loading...