PRACTIXX PX-RRM-2000WI - App Control and Advanced Functions; App Communication and Features; Manual Function Control; Resetting Settings and Cleaning Procedures

w ww.practixx .com
36
|
GB
Example:
You have installed 200 m of boundary wire and set a
value of 25% for zone 1.
After charging, the robotic lawnmower drives 50 m
along the boundary wire and starts mowing from
there.
m NOTE:
This function allows you to start the robotic lawn-
mower in di󰀩cult-to-reach passages, for example, to
ensure a perfect mowing pattern.
9.7 Switching functions on/o󰀨 manually
The following functions can be switched on and o󰀨
manually via the “HOME” button:
• Rain sensor (“RAIN”)
• Mowing zone (“ZONE”)
• LED light (“LED”)
• Ultrasound sensor (“ULT”)
1. Press and hold the “HOME” button until “RAIN”
appears on the display.
2. To scroll down through the functions, press the
“HOME” button (down arrow button). To move up
in the menu, press the “START” button (up ar-
row button).
3. Select the desired function.
4. For “ON”, press the “HOME” button. For “OFF”,
press the “START” button.
5. Conrm your selection with “OK”. “IdLE” ap-
pears on the display.
9.8 Resetting settings
m NOTE:
All settings on the robotic lawnmower (1) are deleted
and reset to the factory settings!
• to reset the settings on the robotic lawnmower,
press the “START”, “HOME” and “OK” buttons
on the operating panel simultaneously for sev-
eral seconds.
10. Cleaning
m ATTENTION!
Switch o󰀨 the product before cleaning with the
-button.
m ATTENTION!
Put on protective gloves before cleaning the rotating
blade carrier.
We recommend that you clean the product directly
after every use.
9.6.2 Communication / data transmission
The app communicates with the robotic lawnmower
either via Bluetooth or WiFi.
m NOTE:
Depending on your contract with your mobile phone
provider or internet provider, the data transfer from
the app to the internet may incur costs that you will
have to bear yourself.
9.6.3 Functions of the app
• Viewing and editing the mowing plan
• Adjusting the mowing zones
• Starting mowing
• Send the device to the charging station
• Switching LED light, rain sensor and ultrasound
sensor on/o󰀨
• Setting the ultrasound sensor range
• Setting the rain delay
• Settings
• Updates / read out (log data)
9.6.3.1 Viewing and editing the mowing plan
With this function you can set when the robotic lawn-
mower should start mowing and how long it should
mow for each individual day.
There is one start time per day (later max. two start
times) available.
In this function you can also set the days on which
the lawn edges are to be mown.
m ATTENTION!
Changing the mowing schedule, starting a mow-
ing operation, switching the automatic on and
o󰀨, sending the robotic lawnmower home and
changing the date and time may result in activ-
ities that are not expected by other people. Af-
fected persons must therefore always be in-
formed in advance about possible activities of
the robotic lawnmower.
9.6.3.2 Adjusting the mowing zones
In this function you can manually set up two di󰀨er-
ent mowing zones in %. By default, the function is
set to “AutoMultizone”. Here, the mower starts after
each charging process at an arbitrary place along
the boundary wire.
This means:
After the rst charging process, the robotic lawn-
mower moves along the boundary wire in accord-
ance with the set % number for zone 1 and starts
mowing.
After the second charging process, it does the same
in accordance with the set % number for zone 2, etc.