EasyManua.ls Logo

Primus MB44 - User Manual

Primus MB44
136 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INDUSTRIAL WASHER EXTRACTORS
HIGH SPIN WASHER EXTRACTORS:
6 kg 33 kg
7 kg 40 kg
10 kg 55 kg
16 kg 120 kg
22 kg
RIGID MOUNTED WASHER EXTRACTORS:
6 kg 18 kg
7 kg 22 kg
10 kg 27 kg
13 kg 35 kg
16 kg 43 kg
HIGH SPIN HYGIENIC BARRIER WASHER EXTRACTORS:
16 kg 66 kg
26 kg 90 kg
33 kg 140 kg
44 kg 180 kg
PROGRAMMING MANUAL
FULL CONTROL
100962 G
Publication date: 24 Jun 2008
SELECT PROGRAM
ABCDEFGHKLMNOPQR
100521

Table of Contents

Questions and Answers

  • M
    Mr. Marc Quinn DDSAug 19, 2025
    How to fix a Primus Scrubber with a display that won't light up?
    • D
      davidhallAug 19, 2025
      If the display of your Primus Scrubber is not illuminated when you switch on the power, consider the following: * Ensure the external power supply is switched on and providing power to the machine. * Deactivate the emergency button. * Check and properly connect the power connector on the board, ensuring correct wiring. * Inspect the fuse on the electronic board; replace it if burned. Also, verify that input signals or the +16Vdc Supply Signal are not touching the cabinet. * If there's no EPROM on the electronic board, install the correct EPROM with the software.
  • M
    Mary HansonAug 21, 2025
    What to do if my Primus MB44 Scrubber keyboard buttons aren't working?
    • R
      Rachel HunterAug 21, 2025
      If your Primus Scrubber is not responding when you press the keyboard buttons, here are some things to check: * Make sure the input connector “A” is securely connected and inspect the wiring between the connector and the key-switch. * Ensure the key switch is set to “Run mode.” * Verify that the connector “K” of the keyboard is properly connected.
  • S
    Sandra PenaAug 23, 2025
    How to improve the display brightness on a Primus MB44 Scrubber?
    • M
      Matthew CarrilloAug 25, 2025
      If the display on your Primus Scrubber is illuminated but hard to read, adjust the brightness setting in the Configuration Menu until the display is clear and bright.
  • A
    Angie JuarezAug 26, 2025
    Why is the drum not turning in my Primus MB44 Scrubber?
    • A
      Ann MurphyAug 26, 2025
      If the drum in your Primus Scrubber isn't turning and no error message is displayed, check the following: * Inspect the belt for any breaks and check its tension; replace or adjust as needed. * Check the motor voltage applied. * Assess whether the motor is still functional. * Check the inverter.
  • S
    Susan PattersonAug 27, 2025
    How to resolve a 'Heating Failure' error on a Primus MB44 Scrubber?
    • B
      Bobby FranklinAug 28, 2025
      If you're encountering a 'Heating Failure' (Failure 13) error on your Primus Scrubber, check if the heating contactor is activated. If it's not, repair the wiring or replace the contactor.
  • Y
    yvonnemartinAug 29, 2025
    What causes outputs to not activate when starting a program on a Primus MB44?
    • J
      Jeffrey CampbellAug 30, 2025
      If you start a program on your Primus Scrubber, but the outputs aren't activating, ensure that connectors “R” and “Q” are correctly connected and not inverted. Pin “Q10” must be supplied with 220Vac when the door is closed.
  • K
    katherine04Sep 1, 2025
    How do I fix a wrong water level issue on my Primus MB44?
    • K
      Kristin FisherSep 1, 2025
      If you're experiencing a wrong water level issue with your Primus Scrubber, make sure the programmed water levels are correct and that the right machine type is selected in the Configuration Menu. You can reinitialize standard water levels by programming new values or reloading the Standard Wash programs.
  • S
    Sara YoungSep 3, 2025
    What should I do if my Primus Scrubber shows an 'Overfill Failure'?
    • L
      Lisa GarciaSep 3, 2025
      If your Primus Scrubber displays an 'Overfill Failure' (Failure 12), the water inlet valves might be broken. Try cleaning or replacing the water inlet valve diaphragms.
  • K
    Katherine JohnsSep 5, 2025
    How to troubleshoot a 'Fill Failure' on a Primus Scrubber?
    • A
      Angela PerezSep 5, 2025
      If you're facing a 'Fill Failure' (Failure 11) on your Primus Scrubber, start by checking if the external water valves are open. If they are closed, open the water inlet valves to allow water to flow into the machine.
  • J
    Joseph CarpenterSep 7, 2025
    What to do if my Primus MB44 displays a 'Too Hot' error?
    • K
      Kari BowmanSep 8, 2025
      If your Primus Scrubber shows a 'Too Hot' (Failure 15) error, verify that the correct water inlet valves have been programmed. Ensure you're programming both hot and cold water inlet valves for the wash sequence.

Summary

Warnings and Symbols

2.1. WARNINGS

Key safety alerts and precautions for operating the machine.

2.2. SYMBOLS USED

Initializing the Machine

4.1 INITIALISATION MENU

Guide to setting up the machine's operational parameters.

4.2 CONFIGURATION MENU

Steps for configuring machine-specific settings.

Programming

5.1 GENERAL

5.2. STEP ①: PROGRAM MENU

Accessing and managing wash programs.

5.3. STEP ②: PROGRAM FUNCTIONS

6. OPERATION MENU

6.1. STARTING UP

Initial steps before operating the machine.

6.2. SWITCHING ON THE POWER

6.3. LOAD THE WASHING MACHINE

6.4. PUT SOAP INTO THE SOAPHOPPER

6.5. STARTING A WASH PROGRAM

Steps to initiate a wash cycle.

Primus MB44 Specifications

General IconGeneral
ModelMB44
CategoryScrubber
Brush TypeDisk
Working Width440 mm
Power SourceBattery
Battery Voltage24 V
Brush Width440 mm
TypeWalk-behind
Battery2 x 12V

Related product manuals