EasyManua.ls Logo

Primus MB180 - User Manual

Primus MB180
136 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INDUSTRIAL WASHER EXTRACTORS
HIGH SPIN WASHER EXTRACTORS:
6 kg 33 kg
7 kg 40 kg
10 kg 55 kg
16 kg 120 kg
22 kg
RIGID MOUNTED WASHER EXTRACTORS:
6 kg 18 kg
7 kg 22 kg
10 kg 27 kg
13 kg 35 kg
16 kg 43 kg
HIGH SPIN HYGIENIC BARRIER WASHER EXTRACTORS:
16 kg 66 kg
26 kg 90 kg
33 kg 140 kg
44 kg 180 kg
PROGRAMMING MANUAL
FULL CONTROL
100962 G
Publication date: 24 Jun 2008
SELECT PROGRAM
ABCDEFGHKLMNOPQR
100521

Table of Contents

Questions and Answers

  • J
    joshuahansenAug 19, 2025
    How to fix a Primus MB180 Scrubber with a display that won't light up?
    • M
      Mr. Theodore BowenSep 12, 2025
      If the display of your Primus Scrubber is not illuminated when you switch on the power, consider the following: * Ensure the external power supply is switched on and providing power to the machine. * Deactivate the emergency button. * Check and properly connect the power connector on the board, ensuring correct wiring. * Inspect the fuse on the electronic board; replace it if burned. Also, verify that input signals or the +16Vdc Supply Signal are not touching the cabinet. * If there's no EPROM on the electronic board, install the correct EPROM with the software.
  • B
    Beverly MejiaAug 21, 2025
    What to do if my Primus MB180 keyboard buttons aren't working?
    • D
      Danielle VasquezAug 21, 2025
      If your Primus Scrubber is not responding when you press the keyboard buttons, here are some things to check: * Make sure the input connector “A” is securely connected and inspect the wiring between the connector and the key-switch. * Ensure the key switch is set to “Run mode.” * Verify that the connector “K” of the keyboard is properly connected.
  • T
    Tiffany MoralesAug 25, 2025
    How to improve the display brightness on a Primus MB180 Scrubber?
    • S
      Sarah HamiltonAug 25, 2025
      If the display on your Primus Scrubber is illuminated but hard to read, adjust the brightness setting in the Configuration Menu until the display is clear and bright.
  • A
    Alyssa MillsAug 26, 2025
    Why is the drum not turning in my Primus MB180?
    • M
      Michael FernandezAug 26, 2025
      If the drum in your Primus Scrubber isn't turning and no error message is displayed, check the following: * Inspect the belt for any breaks and check its tension; replace or adjust as needed. * Check the motor voltage applied. * Assess whether the motor is still functional. * Check the inverter.
  • H
    Heather RoblesAug 27, 2025
    How to resolve a 'Heating Failure' error on a Primus Scrubber?
    • D
      David McmahonAug 28, 2025
      If you're encountering a 'Heating Failure' (Failure 13) error on your Primus Scrubber, check if the heating contactor is activated. If it's not, repair the wiring or replace the contactor.
  • X
    xspencerAug 30, 2025
    What causes outputs to not activate when starting a program on a Primus MB180 Scrubber?
    • H
      hkennedyAug 30, 2025
      If you start a program on your Primus Scrubber, but the outputs aren't activating, ensure that connectors “R” and “Q” are correctly connected and not inverted. Pin “Q10” must be supplied with 220Vac when the door is closed.
  • A
    andersondonnaSep 1, 2025
    How do I fix a wrong water level issue on my Primus Scrubber?
    • N
      newtoncindySep 1, 2025
      If you're experiencing a wrong water level issue with your Primus Scrubber, make sure the programmed water levels are correct and that the right machine type is selected in the Configuration Menu. You can reinitialize standard water levels by programming new values or reloading the Standard Wash programs.
  • J
    Jennifer BakerSep 3, 2025
    What should I do if my Primus MB180 Scrubber shows an 'Overfill Failure'?
    • M
      Matthew DeanSep 3, 2025
      If your Primus Scrubber displays an 'Overfill Failure' (Failure 12), the water inlet valves might be broken. Try cleaning or replacing the water inlet valve diaphragms.
  • K
    kathleen61Sep 5, 2025
    How to troubleshoot a 'Fill Failure' on a Primus MB180?
    • P
      Philip GarciaSep 5, 2025
      If you're facing a 'Fill Failure' (Failure 11) on your Primus Scrubber, start by checking if the external water valves are open. If they are closed, open the water inlet valves to allow water to flow into the machine.
  • J
    John ReyesSep 7, 2025
    What to do if my Primus MB180 Scrubber displays a 'Too Hot' error?
    • L
      lisa82Sep 7, 2025
      If your Primus Scrubber shows a 'Too Hot' (Failure 15) error, verify that the correct water inlet valves have been programmed. Ensure you're programming both hot and cold water inlet valves for the wash sequence.

Summary

Warnings and Symbols

General Warnings

Crucial safety warnings and precautions for operating the washing machine.

Wash Program Creation and Programming

Wash Program Creation Steps

Programming Wash Functions

Machine Setup and Configuration

Initialisation Menu Configuration

Configuration Menu Setup

Configuring machine type, voltage, inverter, and other system parameters.

Operation Menu

Starting Up and Loading Machine

Starting a Wash Program

Troubleshooting and Error Messages

Display and Fault Messages

Understanding and interpreting various display and fault messages during operation.

Handling Fault Messages

Procedures for overruling and erasing fault messages, and safety conditions for door unlocking.

Service Information

Electronic Board and Software Installation

Details on the electronic board and instructions for installing new software.

Primus MB180 Specifications

General IconGeneral
BrandPrimus
ModelMB180
CategoryScrubber
LanguageEnglish

Related product manuals