Pro-Form 660 Vx Treadmill User Manual (English)

Other manuals for Pro-Form 660 Vx Treadmill

User Manual36 pages

Manual Del Usuario34 pages

Bedienungsanleitung36 pages

Gebruiksaanwijzing36 pages

Manuel De L'Utilisateur36 pages

Simple Manual36 pages

Questions and Answers:

J
Jordan TranJul 30, 2025
How to fix Pro-Form 660 Vx Treadmill when the power does not turn on?
- T
  Troy HartJul 31, 2025
  First, ensure the power cord is plugged into a properly earthed outlet. Then, check that the key is inserted into the console after plugging in the power cord. Next, examine the circuit breaker located on the treadmill frame near the power cord; if the switch protrudes, reset it by waiting five minutes and then pressing the switch back in. Finally, verify that the on/off switch located on the treadmill frame near the power cord is in the on position.
N
nnelsonAug 4, 2025
What to do if my Pro-Form 660 Vx turns off during use?
- L
  lawsonmarcusAug 4, 2025
  If your treadmill turns off during use, check the circuit breaker located on the treadmill frame near the power cord. Also, ensure the power cord is securely plugged in; if it is, unplug it, wait five minutes, and plug it back in. Additionally, remove and reinsert the key from the console. Finally, confirm that the on/off switch is in the on position.
R
Ryan MoraAug 10, 2025
How to fix a Pro-Form 660 Vx Treadmill walking belt that is off-centre or slips?
- S
  Steven HodgeAug 10, 2025
  If the walking belt is off-centre, first remove the key and unplug the power cord. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left bolt counterclockwise 1/2 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 5–7 cm (2–3 in.) off the walking platform.
D
Darrell ScottAug 14, 2025
What to do if the display of my Pro-Form 660 Vx console does not function properly?
- D
  Denise SmithAug 14, 2025
  First, remove the key from the console and unplug the power cord. With assistance, carefully tip the Uprights down. Remove the three Screws and the three Hood Screws. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is correct.
T
tyler10Aug 19, 2025
How do I fix the incline on my Pro-Form 660 Vx Treadmill if it doesn't change correctly?
- B
  Benjamin WuAug 19, 2025
  With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key, wait a few seconds, and then reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.
J
jameswilliamsAug 25, 2025
Why does my Pro-Form 660 Vx walking belt slow down when I walk on it?
- J
  James WilliamsonAug 25, 2025
  If the walking belt slows down when walked on, use only a 3-conductor, 1mm[2] (14-gauge) cord that is no longer than 1.5 m (5 ft.) if an extension cord is needed. If the walking belt is overtightened, remove the key and unplug the power cord, then use the hex key to turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 5–7 cm (2–3 in.) off the walking platform.

Pro-Form 660 Vx Treadmill Specifications

General

Motor Power	2.75 CHP
Running Area	20" x 60"
Incline	Yes
Weight Capacity	350 Lbs.
Display	7" Backlit Display
Heart Rate Monitoring	EKG Grip Pulse
Motor	Mach Z Commercial Motor
Incline Range	0% to 12%
Speed Range	0 to 12 MPH
Programs	32 Workout Apps
Folding	SpaceSaver Design with EasyLift Assist