PART LIST-- Model No. 831.299271 RllggA
To locate the
parts listedbelow, refer to the EXPLODED DRAWING attached in the center of this manual.
Key Key Key
No. Qty. Description No. Qty. Description No. Qty. Description
1 1
2 1
3 4
4* 1
5 1
6 1
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38 4
39 4
40 1
41 2
42 1
43 1
44 2
45 2
Motor Belt 46 4 Isolator Screw 93 1 Motor Tension Spacer
Pulley/Flywheel/Fan 47 15 Plastic Fastener 94 1 Motor Hood
Motor Nut 48 1 Shield 95 2 Front Wheel
Motor/Pulley/ 49 2 Belt Guide 96 1 InclineMotor Shield
Flywheel/Fan 50 1 Book Holder 97 4 Base Pad
Incline Motor Bolt 51 1 Front Belly Pan 98 1 12" Audio Wire
Plastic Incline Motor 52 1 Power Supply 99 1 Upright Grommet
Spacer 53 4 Cable Tie Clamp 100 1 Allen Wrench
InclineMotor 54 4 Cable Tie 101 11 Short Screw
Stop Bracket 55 1 Walking Belt 102 1 Lock Knob
Small Nut 56 1 20" Wire Harness 103 2 Extension Leg
Star Washer 57 1 Rear Roller 104 2 Extension Leg Cap
Optic Switch 58 1 Belly Pan Spacer 105 1 Shock
Frame 59 2 Rear Foot 106 1 Choke
Optic Switch Bolt 60 1 Rear Foot Screw 107 2 Pulse Bar Bolt
Incline Optic Disk 61 1 Ground Wire 108 2 Pulse Bar Washer
Incline Motor Nut 62 8 Ground Wire Screw 109 1 Pulse Bar
Hood Screw 63 1 Belly Pan 110 2 Handrail Foam Grip
Plastic Stand-Off 64 1 Rear Endcap 111 1 Lock Knob Sleeve
Hood Bracket (short) 65 2 Rear Roller Adj. Bolt 112 1 Spring
Hood Bracket (long) 66 1 Motor 113 1 Lock Pin Collar
Warning Decal 67 1 Latch Decal 114 1 Pin Clip
Reed Switch 68 4 Platform Screw 115 1 Lock Pin
Reed Switch Clip 69 8 ElectronicsScrew 116 1 Console Base Bottom
Motor/Controller Wire 70 1 Latch Catch 117 2 Upright Endcap
Controller 71 1 Walking Platform 118"* 1 Chest Pulse Sensor
Electronics Bracket 72 5 8" Cable Tie 119 8 Hood Bracket Screw/
CircuitBreaker 73 1 Jack InclineShield Screw
Power Cord 74 1 Motor Tension Bolt 120 1 Rear Foot Spacer
Power Cord Grommet 75 2 Foot Rail Insert 121"* 1 Hand Weight Set
On/Off Switch 76 10 Screw # 1 8" White Wire, 2F
Inlet Bracket 77 1 Console # 1 4" White Wire, M/F
Incline Leg 78 1 Metal Incline Motor # 1 9" Wire Harness
Frame Pivot Bolt Spacer # 1 8" Blue Wire, 2F
Frame Pivot Spacer 79 4 Long Screw # 1 4" Blue Wire, 2F
Upright Wire Harness 80 1 10' I-Fit Wire # 1 4" Black Wire, 2F
Front Roller Adj. Bolt 81 4 Motor Star Washer # 1 4" Green Wire, FIRing
Roller Adj. Washer 82 1 Upright # 1 8" Green Wire, FIRing
Motor Tension Nut/ 83 2 Incline Leg Pivot Bolt # 1 8" Green Wire, 2 Ring
Front Roller Nut 84 2 Side Hood Screw # 1 User's Manual
Motor Bolt 85 2 Handrail Extension
Cap Screw 86 2 Wheel Bolt * Includes all parts shown in the
Left Foot Rail Cap 87 1 Console Base box
Foot Rail 88 1 MotorTension Washer **For more informationabout the
Front Roller/Pulley 89 10 Console/Catch Screw optional hand weight set or chest
Magnet 90 1 Key/Clip pulse sensor, see page 18
Platform Screw (mid) 91 1 Incline Motor Plate # These parts are not illustrated
Isolator 92 1 Right Foot Rail Cap
23
To Next Page
Loading...
