ProForm PFTL59420-INT.0

Questions and Answers

S
scott46Aug 8, 2025
Why does my ProForm PFTL59420-INT.0 Treadmill power turn off during use?
- C
  Catherine PruittAug 8, 2025
  Your ProForm Treadmill might be turning off during use due to several reasons. The power switch may have tripped; if so, check the power switch and reset it by waiting five minutes before pressing it back in. Ensure the power cord is securely plugged in; if it is, unplug it, wait five minutes, and plug it back in. Also, try removing and reinserting the key from the console.
J
Jessica LopezAug 13, 2025
How to fix a ProForm PFTL59420-INT.0 Treadmill that does not turn on?
- J
  Jeff BurgessAug 13, 2025
  If your ProForm Treadmill does not turn on, ensure the power cord is plugged into a properly earthed outlet, using a suitable extension cord if needed (3-conductor, 14-gauge, no longer than 5 ft.). Also, verify that the key is correctly inserted into the console. Finally, check the power switch located on the treadmill frame; if it has tripped, wait five minutes before pressing it back in to reset.
C
Catherine SmithAug 18, 2025
What to do if the ProForm PFTL59420-INT.0 Treadmill walking belt slips when walked on?
- P
  Patricia MasonAug 18, 2025
  If the walking belt on your ProForm Treadmill slips when you walk on it, first remove the key and unplug the power cord. Then, using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. Ensure the walking belt is correctly tightened, allowing you to lift each edge 2 to 3 inches off the walking platform, and keep it centered. Plug the power cord back in, insert the key, and walk on the treadmill for a few minutes. Repeat this process until the walking belt is properly tightened.
T
Tina BellAug 22, 2025
Why do the console displays remain lit after removing the key from my ProForm Treadmill?
- A
  Anita SmithAug 22, 2025
  The console displays on your ProForm Treadmill may remain lit after removing the key because the console features a display demo mode, designed for store displays. To turn off the demo mode, check your console settings.
D
Daniel WrightAug 28, 2025
What to do if ProForm PFTL59420-INT.0 Treadmill walking belt slows when walked on?
- C
  christinehornAug 28, 2025
  If the walking belt on your ProForm Treadmill slows down when you walk on it, use only a 3-conductor, 14-gauge (2 mm[2]) cord that is no longer than 5 ft. (1.5 m) if you need an extension cord. If the walking belt is overtightened, remove the key and unplug the power cord. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform, keeping it centered. Plug in the power cord, insert the key, and walk on the treadmill for a few minutes, repeating until properly tightened. Never apply silicone spray or other substances to the walking belt.
A
Adriana BrownSep 2, 2025
How to fix ProForm PFTL59420-INT.0 Treadmill console displays that do not function properly?
- A
  Amanda BeckSep 2, 2025
  If the console displays on your ProForm Treadmill do not function properly, remove the key and unplug the power cord. Remove the five #8 x 3/4" Screws and pivot off the Motor Hood. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until the Magnet is aligned with the Reed Switch, ensuring a gap of about 3 mm (1/8 in.). If needed, loosen the #8 x 1/2" Washer Head Screws, move the Reed Switch slightly, and retighten the Screws. Reattach the Motor Hood, and walk on the treadmill for a few minutes.

ProForm PFTL59420-INT.0 Specifications

General

Display	LCD
Programs	18
Running Area	46 x 127 cm
Incline	0 – 10%
Speed	0 – 16 km/h
Folding	Yes
Weight Capacity	125 kg
Dimensions	178 x 76 x 140 cm
Speed Range	0 – 16 km/h
Incline Range	0-10%
Running Surface	46 x 127 cm
Dimensions (L x W x H)	178 x 76 x 140 cm
Weight	73 kg