-7-
Ta
ble 1
Minimum gage for cord
Effective date for Ta ble 1changed from November 1, 1995 to
November
11, 1996
AmpereRating Volts To tal length of cordinfeet
120
V25ft. 50 ft. 100 ft. 150 ft.
240 V50ft. 100 ft. 200 ft. 300 ft.
MoreNot MoreAWG
Than
Than
06
18 16 16 14
61018161412
10
12 16 16 14 12
12 16 14 12 Not Recommended
Legend (Fig. 1)
1. Main spindle
2. Lathe chuck
3. Turning tool holder
4. Rotating centre
5. Flange surface for milling unit
6. Sleeve
7. Clamp screw for sleeve
8. Ta ilstock
9. Sleeve adjusting handwheel
10. Handwheel for leadscrew
11. Clamp screw for tailstock
12. Leadscrew
13. Adjusting handwheel for top slide
14. To pslide
15. Support
16. Cross-slide
17. Adjusting handwheel for cross-slide
18. Clutch switch for automatic feed
19. Drive gearbox cover with speed table
20. Switch for anticlockwise rotation stop clockwise rotation
21. Main switch
22. Function display
23. Control
24. Hollow hexagon wrench
25. Lathe chuck wrench
Description of the machine
The PROXXON lathe PD 250/E is an extensible system which
consists of
•
solid shaft electronics for high torques over the entirespeed range
•automatic feed
•lathe chuck and
•rotating centre
for machining steel, brass, aluminium and plastics.
It can also be used for face turning, longitudinal turning and
thread cutting.
The machine is also suitable for boring, milling work and grooving
by using the appropriate accessories.
The ribbed, grey cast iron machine bed with ground prismatic
guideways ensures vibration-free work.
Warning
This Lathe is for indoor use only.Donot expose to rain or use in
damp locations.
Do
not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alternation or modi-
fication
is misuse and could result in hazardous condition leading
to possible serious injury.
Technical data:
Centredistance 9.8” (250 mm)
Centreheight 2.76" (70 mm)
Height above support 1.7" (43 mm)
Holding capacity
–Inner jaws 0.1" to 1.1" (2 -27mm)
–Outer jaws 1" to 2.8" (25 -75mm)
Cross-slide travel 2.4" (60 mm)
Topslide adjustment 1.8" (45 mm)
Spindle
bore0.4" (10.5 mm)
Nose support on chuck side MK1/short
Tool holder 0.3" x0.3" (8x8 mm)
Machine dimensions approx. 22" x10,63" x6,7"
(560 x270 x170 mm)
Weight approx. 26,5 lb
Possible thread leads 0.5, 0.625, 0.7, 0.75, 0.8, 1.0, 1.25, 1.5 mm
Spindle speeds
–byshifting the V-belt 300/900/ and 3000 rpm
–bycontrol 25% to 100%
Feed 0.05 and 0.1 mm/revolution
Sleeve motion 1.2”
Sleeve for morse taper MK 1/short
Motor
Voltage: 115 Volt, 60 Hz,~
Power consumption 140 Watt
Noise emission 70 dB (A)
Only to be operated in closed rooms!
Do not dispose of the electrical device
in the household waste!
Always work with hearing protection!
Wear safety glasses!
Installation and setting up
Warning
To avoid injury from unexpected starting or electrical shock, do not
plug the power cordinto apower source receptacle during
unpacking and assembly.This cordmust remain unplugged
whenever you areworking on the lathe.
If any part is missing or damaged, do not plug the lathe in until the
missing or damaged part is replaced, and assembly is complete.
To avoid electrical shock, use only identical replacement parts
when servicing grounded tools.
To Next Page
Loading...
