Pyronix Enforcer 32WE Setup Guide

26
SHOCK-WE
Wireless transmitter with wall tamper and shock sensor
Descriptions
1. Tri-Colour LED: When the sensor detects a vibration, the LED will illuminate in one of two colours:
GREEN: Pre-Alarm Detection, but the alarm threshold not yet reached
BLUE: Alarm
If only the GREEN LED illuminates, the sensitivity of the unit may need increasing. Please see “7.
Potentiometer and Sensitivity Range” to increase the sensitivity.
4. Reset Button: To learn the wireless transmitter on the radio expander, the reset button needs to
be pressed after the battery is installed. For full programming on this procedure, please refer to the
expander manual.
7. Potentiometer and Sensitivity Range: The sensitivity can be either increased or decreased using
the potentiometer and sensitivity link.
2. Background Disturbance: If there is a constant background
disturbance then this can be ltered out by tting the background
disturbance link which will monitor for this.
3. LED Enable: If this link is removed, the tri-colour LED will be
disabled at all times, which will save battery life.
5. Pulse 4: If this link is tted, a count of 4 pulses (GREEN LED) in
a rolling 30 second window, will generate an alarm activation.
6. Pulse 2: If this link is tted, a count of 2 pulses (GREEN LED)
in a rolling 30 second window, will generate an alarm activation.
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
Electrical Specification Sensitivity
Voltage: >2.5V High range sensitivity band
Current: 12uA Low range sensitivity band
Disturbance: Rolling 30s period
Battery
Life: Greater than 2 years Operating Environment
CR2 3.0 Volt -10 to 50°C
+
-
Battery
LEDs
Front Tamper
Rear Tamper
Learn Button
Disabled
Enabled
Disabled
Enabled
Enabled
Disabled
Enabled
Disabled
Low Range Sensitivity Band: High Range Sensitivity Band:
Link Off and Turn
potentiometer right for
more sensitive and left
for less sensitive
Link On and Turn
potentiometer right for
more sensitive left for
less sensitive
CR2 BATTERY
+
-
Background
Disturbance
LED Enable
Pulse
Count 4
Pulse
Count 2
Low/High
Sensitivity
Sensitivity
Band
LEARN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
Electrical Specification Sensitivity
Voltage: >2.5V High range sensitivity band
Current: 12uA Low range sensitivity band
Disturbance: Rolling 30s period
Battery
Life: Greater than 2 years Operating Environment
CR2 3.0 Volt -10 to 50°C
+
-
Battery
LEDs
Front Tamper
Rear Tamper
Learn Button
Disabled
Enabled
Disabled
Enabled
Enabled
Disabled
Enabled
Disabled
Low Range Sensitivity Band: High Range Sensitivity Band:
Link Off and Turn
potentiometer right for
more sensitive and left
for less sensitive
Link On and Turn
potentiometer right for
more sensitive left for
less sensitive
CR2 BATTERY
+
-
Background
Disturbance
LED Enable
Pulse
Count 4
Pulse
Count 2
Low/High
Sensitivity
Sensitivity
Band
LEARN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
Electrical Specification Sensitivity
Voltage: >2.5V High range sensitivity band
Current: 12uA Low range sensitivity band
Disturbance: Rolling 30s period
Battery
Life: Greater than 2 years Operating Environment
CR2 3.0 Volt -10 to 50°C
+
-
Battery
LEDs
Front Tamper
Rear Tamper
Learn Button
Disabled
Enabled
Disabled
Enabled
Enabled
Disabled
Enabled
Disabled
Low Range Sensitivity Band: High Range Sensitivity Band:
Link Off and Turn
potentiometer right for
more sensitive and left
for less sensitive
Link On and Turn
potentiometer right for
more sensitive left for
less sensitive
CR2 BATTERY
+
-
Background
Disturbance
LED Enable
Pulse
Count 4
Pulse
Count 2
Low/High
Sensitivity
Sensitivity
Band
LEARN

Pyronix Enforcer 32WE Specifications

General

Brand	Pyronix
Model	Enforcer 32WE
Category	Security System
Language	English