To Next PageTo Next PageWhat to do if all LED Lights are off on the Q'STRAINT QLK-150 Dash Control?
All LED Lights are off on the Q'STRAINT Wheelchair Dash Control because the vehicle needs to be turned ON in order for the LED lights to work.
What to do if Q'STRAINT Docking Station does not open with Dash Control/aux release switch?
If the Q'STRAINT docking system doesn't open when you use the Dash Control or auxiliary release switch, check that the voltage supplied to the QLK system is more than 12V when QLK is activated. Also, ensure that the docking bolt/bracket isn't applying pressure to the locking pawl.
How to manually release a wheelchair from Q'STRAINT Docking Station?
To manually release the wheelchair from the Q'STRAINT Docking Station, push the Manual Release Lever. This will open the Locking Pawl and release the wheelchair.
Why is the green light on my Q'STRAINT Docking Station Dash Control not turning on?
If the green light on the Q'STRAINT Docking Station Dash Control won't turn on, it could be because the wheelchair isn't fully secured, meaning the Locking Pawl is still open. Alternatively, the Dash Control Wire Harness might not be properly connected to the Electrical Control Module (ECM). Ensure the wheelchair is secured, and check the connection of the Dash Control Wire Harness to the ECM.
What to do if the red light on Q'STRAINT Docking Station turns on and off?
If the red light on your Q'STRAINT Docking Station Dash Control turns on and then off, it means the wheelchair isn't secured in the Docking System, and the Locking Pawl is still open. Make sure to properly secure the wheelchair in the Docking System.
What to do if the Release Button on the Q'STRAINT QLK-150 Wheelchair Dash Control Panel and the Auxiliary Release Switch are not working?
The Release Button on the Q'STRAINT Wheelchair Dash Control Panel and the Auxiliary Release Switch will not work if the vehicle is turned OFF. This is a safety feature.
Why is the Green Light on the Q'STRAINT Wheelchair Dash Control Panel not turning on?
The green light on the Q'STRAINT Wheelchair Dash Control Panel will not turn on because the wheelchair is not secured in the Docking System. Consequently, the Locking Pawl remains open.
How do I turn on the steady audio beep on Q'STRAINT QLK-150 Wheelchair?
To turn on the steady audio beep after it’s been turned off, you must reset the Q'STRAINT Wheelchair Docking System. This is done by turning off the vehicle and then turning it back on.
How to turn off steady audio beep on Q'STRAINT?
To turn off the steady audio beep on your Q'STRAINT device, press the Touchable Surface to mute it.
Why are all the lights off on my Q'STRAINT Docking Station dash control?
If all the lights are off on the Dash Control of your Q'STRAINT Docking Station, it means the Locking Pawl is open, and the wheelchair isn't secured in the Docking System. Secure the wheelchair in the Docking System.
General| Brand | Q'STRAINT |
|---|---|
| Model | QLK-150 |
| Category | Wheelchair |
| Language | English |
Comprehensive step-by-step guide for installing the QLK-150 Q04BR001 Wheelchair Bracket.
Ensure all installation instructions are read, understood, and followed.
Reach out to the nearest Q'STRAINT office for any inquiries.
Consult separate Installation Instructions and Use and Care Manual for the QLK Docking system.
Critical safety information and recommendations for using Q'STRAINT products.
Q'STRAINT recommends using tested brackets designed for specific transportable wheelchairs.
The Q04BR001 is universal but not tested with specific wheelchair models for vehicle use.
Modifications or alterations to the bracket are the installer's responsibility.
Test drive the wheelchair after bracket installation to ensure correct functionality.
List of required hardware including nuts, bolts, and washers for installation.
Diagram illustrating the main bracket, cross bar, stabilizer V-bracket, and clamps.
Instructions for cutting cross bars to fit wheelchair frame rails.
Guide for attaching bracket clamps and cross bars to wheelchair frame rails.
Positioning the main bracket (center strap) relative to the wheel axis.
Aligning the V bracket to ensure clearance for foot rests and other obstructions.
Specifies hole sizes for center strap, cross bars, clamps, and V bracket stabilizer.
Securing the bracket components using provided hardware and adjusting docking bolt height.
Diagram showing preferred and optional zones for wheelchair placement.
Contact details for Q'STRAINT Europe, America, and Australia for technical support.
