QNAP TS-130 User Manual

LED Status Description
System Status Flashes green and red
alternately every 0.5
seconds
• The drive is being formatted.
• The device is being initialized.
• The operating system is being updated.
• The firmware is being updated.
Note
When updating the firmware, do not remove
the power cord or USB cable, and do not
force-exit the application.
Red • The drive is invalid.
• The disk volume has reached its full capacity.
• The disk volume is about to reach its full capacity.
• The system fan is not functioning.
• An error occurred when accessing (read/write) the
data.
• A bad sector is detected on the hard drive.
• A hardware self-test error occurred.
Flashes green every 0.5
seconds
• The device is not configured.
• A drive is not formatted.
Green The device is ready.
Off • All drives are in standby mode.
• The device is powered off.
LAN Orange The network connection is operating at 1 Gbps.
Flashes orange The device is being accessed from the network.
Off The device is not connected to a network.
Drive Flashes red The data is being accessed and a read/write error occurs
during the process.
Red A drive read/write error occurred.
Flashes green Data is being accessed.
Green The drive is ready.
Off No drive was detected.
1 Gigabit
Ethernet speed
Green The network connection is operating at 1 Gbps.
Orange The network connection is operating at 100 Mbps.
Off There is no network connection.
1 Gigabit
Ethernet activity
Green A network connection has been established.
Flashes green The device is being accessed from the network.
Off There is no network connection.
TS-130 User Guide
Basic Operations 24

QNAP TS-130 Specifications

General

RAID support	-
Hot-swap drive bays	Yes
Storage drive capacity	0 GB
Supported file systems	FAT32, HFS+, NTFS, ext3, ext4
Storage drive interface	Serial ATA II, Serial ATA III
Storage drives installed	No
Storage drive sizes supported	2.5, 3.5 \
Supported storage drive types	HDD & SSD
Total installed storage capacity	0 TB
Number of storage drives installed	0
Number of storage drives supported	1
Processor cores	4
Processor model	RTD1295
Processor frequency	1.4 GHz
Processor manufacturer	Realtek
Flash memory	4000 MB
Internal memory	1 GB
Internal memory type	DDR4
Ethernet LAN data rates	1000 Mbit/s
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Chassis type	Tower
Cooling type	Active
Fan diameter	50 mm
Product color	White
LED indicators	HDD, LAN, Status, System
Number of fans	1 fan(s)
Type	NAS
Noise level	15.2 dB
Device class	Home & Home Office
Operating system version	5.0.0
Operating system installed	QNAP QTS
Mac operating systems supported	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks
Server operating systems supported	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Windows operating systems supported	Windows 10, Windows 7, Windows 8
Fan voltage	12 V
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power supply location	External
Power consumption (typical)	7.29 W
Power consumption (HDD standby)	- W
Power supply unit (PSU) capacity	36 W
Cables included	AC, LAN (RJ-45)
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	5 - 95 %
Harmonized System (HS) code	84714100

Weight and Dimensions

Depth	157.6 mm
Width	66.1 mm
Height	187.5 mm
Weight	610 g
Package weight	1220 g